Bedienungsanleitung Ag neovo PN55H (Seite 71 von 76) (Englisch)

672476

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

APPENDIX

• If a vertical and horizontal frequency-select mode exists, select 60Hz (vertical) and 31.5KHz (horizontal). In

some cases, abnormal signals (such as stripes) might appear on the screen when the PC power is turned

off (or if the PC is disconnected). If so, press the [INPUT] button to enter the video mode. Also, make sure

that the PC is connected.

• When horizontal synchronous signals seem irregular in RGB mode, check PC power saving mode or cable

connections.

• The display settings table complies to the IBM/VESA standards, and based on the analog input.

• The DVI support mode is regarded as same to the PC support mode.

• The best timing for the vertical frequency to each mode is 60Hz.

6.4 Cleaning

Caution When Using the Display

• Do not bring your hands, face or objects close to the ventilation holes of the display. The top of the display

is usually very hot due to the high temperature of exhaust air being released through the ventilation holes.

Burns or personal injuries may occur if any body parts are brought too close. Placing any object near the

top of the display could also result in heat related damage to the object as well as the display itself.

• Be sure to disconnect all cables before moving the display. Moving the display with its cables attached may

damage the cables and thus cause re or electric shock.

• Disconnect the power plug from the wall outlet as a safety precaution before carrying out any type of

cleaning or maintenance procedure.

Front Panel Cleaning Instructions

• The front of the display has been specially treated. Wipe the surface gently using only a cleaning cloth or a

soft, lint-free cloth.

• If the surface becomes dirty, soak a soft, lint-free cloth in a mild detergent solution. Wring the cloth to

remove excess liquid. Wipe the surface of the display to remove dirt. Then use a dry cloth of the same type

to dry.

• Do not scratch or hit the surface of the panel with ngers or hard objects of any kind.

• Do not use volatile substances such as insert sprays, solvents and thinners.

Cabinet Cleaning Instructions

• If the cabinet becomes dirty, wipe the cabinet with a soft, dry cloth.

• If the cabinet is extremely dirty, soak a lint-free cloth in a mild detergent solution. Wring the cloth to remove

as much moisture as possible. Wipe the cabinet. Use another dry cloth to wipe over until the surface is dry.

• Do not allow any water or detergent to come into contact with the surface of the display. If water or

moisture gets inside the unit, operating problems, electrical and shock hazards may result.

• Do not scratch or hit the cabinet with ngers or hard objects of any kind.

• Do not use volatile substances such as insert sprays, solvents and thinners on the cabinet.

• Do not place anything made from rubber or PVC near the cabinet for any extended periods of time.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ag neovo PN55H Seite 71

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Ag neovo PN55H

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info