488259
19
Zoom out
Zoom in
Vorherige Seite
1/53
Nächste Seite
sensor 505-D
User manual
i
Thank you for purchasing this AgfaPhoto digital camera. Please read these operating
instructions carefully in order to use the digital camera correctly. Keep the instructions in a
safe place after reading so that you can refer to them later.
Notice: This User's Manual has been written for the following camera models:
AgfaPhoto sensor 500-D, AgfaPhoto sensor 505-D and AgfaPhoto sensor 510-D.
Precautions
Before using the camera, please ensure that you read and understand the safety
precautions described below. Always ensure that the camera is operated correctly.
Do not point the camera directly into the sun or other intense light sources which could
damage your eyesight.
Do not try to open the case of the camera or attempt to modify this camera in any way.
High-voltage internal components create the risk of electric shock when exposed.
Maintenance and repairs should be carried out only by authorized service providers.
Do not fire the flash too close to the eyes of animals or people, especially young children.
Eye damage may result. In particular, keep at least one meter away from infants when
using the flash.
Keep the camera away from water and other liquids. Do not use the camera with wet
hands. Never use the camera in the rain or snow. Moisture creates the danger of electric
shock.
Keep the camera and its accessories out of the reach of children and animals to prevent
accidents or damage to the camera.
If you notice smoke or a strange odor coming from the camera, turn the power off
immediately. Take the camera to the nearest authorized service center for repair. Never
attempt to repair the camera on your own.
Use only the recommended power accessories. Use of power sources not expressly
recommended for this equipment may lead to overheating, distortion of the equipment,
fire, electrical shock or other hazards.
ii
Disclaimer
We assume no responsibility over and above the provisions of the Product Liability Law
for damages suffered by the user or third parties as a result of inappropriate handling of
the product or its accessories, or by their operational failure and by their use. We reserve
the right to make changes to this product and its accessories without prior notice.
Warning! Never open the camera or remove any parts of it. This will void all guarantee
claims
.
Using your batteries
For best performance and prolonged battery life, we recommend the use of AAA-sized
rechargeable NiMH batteries.
Extending battery life
The following functions use up a great deal of battery power and should therefore only be
used occasionally:
Excessive use of flash
Editing images on the camera display
The battery life can be affected by soiling. Please clean the contacts with a clean, dry
cloth before putting the batteries in the camera. Battery performance drops at
temperatures below 5° C (41° F). If you use the camera at low temperatures you should
have replacement batteries to hand and ensure they do not get too cold. Please note: you
should not dispose of cold and seemingly flat batteries because these batteries may work
again at room temperature.
ii
i
Contents
PRECAUTIONS I
DISCLAIMER II
USING YOUR BATTERIES II
EXTENDING BATTERY LIFE II
CONTENTS ________________________ III
GETTING STARTED __________________ 1
USING THIS MANUAL 1
PACKAGE CONTENTS 2
PARTS OF THE CAMERA 3
ATTACHING THE STRAP 5
INSERTING THE BATTERIES 5
LOW BATTERY INDICATOR 6
INSERTING A MEMORY CARD 6
ABOUT CAMERA MEMORY 7
TURNING POWER ON & OFF 7
POWER SAVING FUNCTION 7
SETTING THE DISPLAY LANGUAGE / DATE &
TIME 8
SETTING DISPLAY LANGUAGE 8
SETTING DATE & TIME 9
USING THE LCD MONITOR 9
CAPTURE MODE 10
VIDEO MODE 11
PLAYBACK MODE 12
BASIC OPERATION _________________ 13
TURNING POWER ON & OFF 13
CHANGING THE MODE 13
SWITCHING BETWEEN REC AND PLAYBACK
MODE 13
SELECTING THE REC MODE 14
USING THE MENU IN REC MODE 15
CAPTURE MENU LIST 16
VIDEO MENU LIST 16
SETUP MENU 17
BASIC RECORDING_________________ 19
RECORDING STILL IMAGES 19
SELECTING THE RESOLUTION AND QUALITY
20
USING THE ZOOM FUNCTION 21
USING THE FLASH 22
USING THE SELFTIMER 23
USING THE BURST-SNAPSHOT 24
RECORDING MOVIE CLIPS 25
SETTING THE MOVIE SIZE 25
RECORDING AUDIO 26
PLAYING BACK AUDIO 26
OTHER RECORDING FUNCTIONS _____ 27
SETTING THE WHITE BALANCE 27
SETTING THE COLOR EFFECT 28
SETTING THE EXPOSURE 28
SETTING DATE STAMP 29
PLAYBACK ________________________ 30
PLAYING BACK IMAGES 30
PLAYING BACK MOVIE CLIPS 30
USING THE MENU IN PLAYBACK MODE 31
USING THE MENU IN PLAYBACK MODE 31
VIEWING THUMBNAILS 32
PLAYING A SLIDE SHOW 32
DELETING FILES 33
DELETING A SINGLE FILE 33
DELETING ALL FILES 34
FORMATTING THE SD CARD OR INTERNAL
MEMORY 34
iv
PROTECTING FILES 35
CHOOSING A STARTUP IMAGE 36
SETTING THE LOGO 36
EDITING IMAGES 37
ROTATING STILL IMAGES 37
PRINTING 38
MAKING CONNECTIONS_____________ 39
CONNECTING THE CAMERA TO A TV 39
CONNECTING THE CAMERA TO A PC 40
USING A CARD READER (NOT INCLUDED) 40
CONNECTING THE CAMERA TO A PC WITH
THE USB CABLE 40
SYSTEM REQUIREMENTS ___________ 41
APPENDIX_________________________ 42
ABOUT THE FOLDER & FILE NAMES 42
FOLDER STRUCTURE 42
NAMING FILES 42
TROUBLESHOOTING 43
SPECIFICATIONS 44
CUSTOMER CARE 46
DISPOSAL OF WASTE EQUIPMENT BY USERS
IN PRIVATE HOUSEHOLDS IN THE EUROPEAN
UNION 47
FCC COMPLIANCE AND ADVISORY 47
1
Getting Started
Using This Manual
Getting Started
This section contains information you should know prior to using this camera.
Basic Operation
This section explains all recording features of the camera.
Basic Recording
This section explains how to record still images, movies and audio files.
Other Recording Functions
This section explains common operations when recording images.
Playback
This section explains playback, delete and edit functions of still images, movies and
audio files.
Making Connections
This section explains how to connect the camera to a computer or TV.
Appendix
This section provides troubleshooting and the camera specifications.
The meanings of the symbols used in this user's manual are explained below:
This indicates warnings that should be read before using these
functions.
This indicates useful information for the use of this camera.
This indicates the reference page.
2
Package Contents
AgfaPhoto sensor USB / AV cable 2 x AAA batteries
noitallatsnI erawtfoS partS hcuoP
CD-ROM
Quick guide
3
Parts of the Camera
1. Flash
2. Self-timer lamp
3. Microphone
4. Lens
5. Operation lamp
6. LCD display
Five-way control button
7. Vertically (OK)
8. Rightward
9. Downward
10. Upward
11. Leftward
12. Playback button
13. Menu button
4
4. Shutter button
15. Mode button
16. Power button
17. Strap mount
18. Battery cover
19. USB jack
20. Tripod socket
5
Attaching the Strap
Attach the strap to your camera as shown
in the image.
y Do not swing the camera around by the strap
Inserting the Batteries
The camera is powered by two AAA-size alkaline batteries or rechargeable NiMH
batteries.
Open the battery cover.
Slide the battery cover in the
direction indicated by the arrows.
Insert the batteries.
Insert two AAA-size batteries
with the positive (+) and
negative (-) poles matching the
directions indicated inside the
battery compartment.
Close the battery cover.
2
3
C
C
a
a
u
u
t
t
i
i
o
o
n
n
1
6
Low Battery Indicator
A low battery indicator
appears on the LCD screen when the batteries are nearly
exhausted. Batteries should be replaced promptly when the low battery indicator
appears.
There is a risk of explosion if the battery is replaced by an incorrect type.
Dispose of used batteries according to instructions.
Be sure to turn off the camera power before inserting or removing batteries.
Use only Alkaline or NiMH batteries to power this camera. Use of any other type
of battery is not recommended.
Replace all batteries at the same time. Never mix old and new batteries.
Remove batteries if you will not be using the camera for a long time.
The camera body may feel warm after extended use. This is normal.
Inserting a Memory Card
You can use an SD card with this digital camera. The memory card slot is adjacent to the
battery compartment.
Open the battery cover.
Slide the battery cover in the
direction indicated by the arrows.
Insert the card.
Insert the card with the label facing
up and the arrow pointing inwards.
To remove the card, gently press on the edge of the card to release it. Pull the
card out and close the battery cover.
Close the battery cover.
C
C
a
a
u
u
t
t
i
i
o
o
n
n
1
2
T
T
i
i
p
p
s
s
3
7
If you insert or remove the card while the camera is powered on, it may damage
the card or data.
Do not touch the connection terminals on the back of the card.
About Camera Memory
This camera is equipped with an internal memory. If a memory card is not inserted in the
camera, all images and movie clips recorded by the camera will be stored in the internal
memory. If a memory card is inserted, images and movie clips will be stored on the
memory card.
Turning Power On & Off
Press the Power button (1) to turn on the
camera in the Capture mode. The power
turns on and the LED (2) lights red.
Press the Power button (1) again to turn the power off. The power turns off and
the LED turns off.
You can turn on the camera without the startup and operating sound by setting
the function [Play Logo] and [Buzzer].
Switch between Capture mode and Playback mode ( page 13).
Power Saving Function
To save battery power, the LCD monitor automatically turns off 30 seconds after the last
control accessed (factory-preset setting). Press any button other than the power button
to turn on the LCD monitor. After the power saving function has been active for the set
time, the power will turn off completely. Press the power button to power the camera
back on. You can change the power-off timeout by setting the function [auto power off
time] in the Setup menu.
C
C
a
a
u
u
t
t
i
i
o
o
n
n
1
T
T
i
i
p
p
s
s
2
8
The power saving feature will not activate in the following situations:
y When recording movie clips or audio files
y When playing movie clips or audio files
y When playing the slideshow
y When connecting the camera to a computer or printer with the USB cable
Setting the Display Language / Date & Time
When using the camera for the first time after purchasing it, be sure to choose a
language and set the date & time before using the camera.
Setting Display Language
Turn the power on, and set the camera
to the Setup Menu (
page 17).
Select [Language].
Press
or to select [Language]
then press
to launch the submenu.
Select a language.
Press or on the five-way control button to select a language and press
OK/Enter button to apply the setting.
Press the MENU button to close the menu.
2
4
C
C
a
a
u
u
t
t
i
i
o
o
n
n
3
1
9
Setting Date & Time
Turn the power on, and set the camera
to the Setup Menu (
page 17).
Select [Date/Time].
Press
or on the five-way control
button to select [Date/Time] and then
press on the five-way control button to
launch the submenu.
Set date and time.
Press or on the five-way control button to change the highlighted value. Press
on the five-way control button to move the cursor between settings.
y Holding down
or changes the values continuously. For date stamp setting
(
page 29).
Apply the setting.
After adjusting the settings, press OK/Enter to apply the setting. Finally press the
MENU button to close the setup menu.
Using the LCD Monitor
The LCD monitor is used to compose images while recording, adjust settings and play
back images. The following indicators may appear on the LCD monitor while recording
or playing back images.
2
1
3
T
T
i
i
p
p
s
s
4
10
Capture Mode
1
Capture mode
2
Resolution indicator
2592 x 1944
2048 x 1536
1600 x 1200
1280 x 960
640 x 480
3
White balance indicator:
Cloudy
Daylight
Fluorescent
Tungsten
Auto
4
Quality indicator:
Super
Fine
Normal
5
Memory card inserted
6
Date stamp
7
Images taken/image capacity
8
EV value
-2.0EV-------------2.0EV
9
Battery level indicator:
10
Selftimer indicator:
11
Empty
Half
Full
20 seconds
10 seconds
11
Digital zoom bar
Video Mode
1
Video mode
2
Resolution indicator:
640 x 480
320 x 240
3
White balance indicator:
Cloudy
Daylight
Fluorescent
Tungsten
Auto
4
Memory card inserted
5
Recording time
6
Battery level indicator:
Empty
Half
Full
7
Digital zoom bar
12
Playback Mode
1
Playback mode:
Audio file
Video file
Still image
2
Protect indicator
3
Number of current file/total number
of recorded files
4
Battery level indicator:
Empty
Half
Full
13
Basic Operation
Turning Power On & Off
Press the Power button (1) to turn on the
camera in the Capture mode. The power
turns on and the LED (2) lights red.
Press the Power button (1) again to turn the power off. The power turns off and
the LED turns off.
You can turn on the camera without the startup and operating sound by setting
the function [Play Logo] and [Buzzer].
Switch between Capture mode and Playback mode ( page 13).
Changing the Mode
You can record images and voices in the REC mode and use the Playback mode to
replay, delete or edit images on the LCD monitor.
Switching between REC and Playback Mode
In REC mode, press the Playback button
(2) to switch to the Playback mode.
In Playback mode, press the Playback
button (2) to switch to the REC mode.
1
T
T
i
i
p
p
s
s
2
14
Selecting the REC Mode
Press the Power button to enter the Capture mode.
If the camera is in Playback mode, press the Playback button to change to REC
mode.
Press the Mode button (1) to change the REC mode.
Each time the Mode button is pressed the REC mode icon changes. It includes
three modes in REC mode: Capture mode, Video mode and Audio mode.
The Mode button will not work when the camera is in Playback mode.
Display Title Description
Capture mode For taking still photos.
Video mode For recording movie clips.
Audio mode For recording audio files.
C
C
a
a
u
u
t
t
i
i
o
o
n
n
1
2
15
Using the Menu in REC Mode
When a menu is displayed, the five-way control button is used to make the desired
settings. The Audio mode does not have a menu so the MENU button will not work in
Audio mode.
Capture menu.
Turn the power on, and set the camera to
the Capture mode (
page 13).
Open the Capture menu.
Press the MENU button (2) to display the
menu.
Select an item.
Press or on the five-way control button (1) to select an item.
Change the setting.
Press on the five-way control button (1) to launch the submenu. Press or
on the five-way control button (1) to change the setting.
Press OK/Enter on the five-way control button (1) to save the settings and finally
press the MENU button (2) to close the menu
2
1
3
4
5
16
Capture Menu List
Menu item
Available settings
Resolution
/ / / /
Quality
/
White balance
Color effect
Color / Sepia / Monochrome
Exposure -2.0EV-------------2.0EV
Date stamp
Enable
/ Disable
Selftimer
Disable / 10 sec.
/ 20 sec.
Burst-Snapshot
Single/ Burst
Video Menu List
Set the camera in Video mode then press the MENU button to display the menu.
Menu item
Available settings
Resolution
640 x 480/ 320 x 240
Frame rate 30 fps / 15 fps
White balance
Audio
Enable / Disable
/
/ / /
/
/ / /
/
17
Setup Menu
Turn the power on and set the
camera to the REC or
Playback mode ( page 13).
Press the MENU button (2) to open
the REC or Playback menu. The
menu displayed depends on
whether you are in the REC mode
or the Playback mode.
Open the Setup menu.
Press on the five-way control button (1) to select [Setup] to display the
Setup menu.
Select an item.
Press or on the five-way control button (1) to select a menu item then
press on the five-way control button (1) to launch the submenu.
Change the setting.
Press or on the five-way control button (1) to select an option and press
OK/Enter (1) to apply the setting.
Press the MENU button (2) to close the menu.
5
6
1
2
4
3
18
Menu item Function
Language
Select a language for the Display menu and other information from the
following languages: [English]: English, [Italiano]: Italian, [Français]: French,
[Nederlands]: Dutch, [Čestina]: Czech, [Русский]: Russian, [Türk]: Turkish,
[Deutsch]: German, [Español]: Spanish, [Português]: Portuguese, [Magyar]:
Hungarian, [Polski]: Polish, [Ελληνικά]: Greek, [体中文]: S. Chinese
[日本語] Japanese
Auto
power off
To save power, the camera is turned off automatically after a period of time.
There are three options: [Disable] / [60Sec] / [120Sec].
TV output
You can review images on a television with the supplied AV cable. TV Out
should be set to either NTSC or PAL depending on your region.
[NTSC]: America, Japan and others; [PAL]: Europe, Oceania and others.
Play logo
Use this function to turn the startup image on or off. [Enable] / [Disable]
Light
frequency
Light Frequency should be set to either 60Hz or 50Hz depending on your
region. [50HZ] / [60HZ].
Date /
Time
To record the shooting date and time.
Buzzer
Sets the operation sound on and off. [Enable] / [Disable]
Format
To erase all data stored on the memory card if you are using a memory card, or
all data stored in the internal memory if there is no card inserted. All data will
be deleted including protected files. Be sure to download important files to your
computer before formatting. [Yes] / [No].
Default
settings
To reset the entire menu and button operation settings to initial default.
The Date & Time settings do not change after reset all.
USB mode
You can use this camera as a PC camera or removable disk. [PC Camera]:
Use as a PC camera; [Mass storage]: Use as a removable disk.
19
Firmware
This function will show the software version.
Basic Recording
Recording Still Images
Turn the power on, and set the
camera to the Capture mode.
( page 13).
Compose the subject on the
monitor.
Point the center area of the LCD
screen at the subject that you want to
take a photo of.
Take the picture.
Press the shutter button fully down to take the picture.
Make sure that your fingers or the wrist strap do not cover the lens.
Do not take the memory card or battery out when the camera is saving the
image, otherwise the image will not be saved completely
1
2
C
C
a
a
u
u
t
t
i
i
o
o
n
n
3
20
Selecting the Resolution and Quality
You can select a lower image resolution and quality to decrease the image size in order
to capture more images. Choose a suitable setting according to the desired image
quality and purpose.
Image size
AgfaPhoto sensor 505-D
Picture size
2592 x 1944
2048 x 1536
1600 x 1200
1280 x 960
640 x 480
Printing larger than A4 size
Printing to postcard or attaching
to E-mail
Larger
Smaller
Image size
AgfaPhoto sensor 510-D
Picture size
3264 x 2448
2592 x 1944
2048 x 1536
1600 x 1200
640 x 480
Printing larger than A4 size
Printing to postcard or attaching
to E-mail
Larger
Smaller
Image size
AgfaPhoto sensor 500-D
Picture size
2592 x 1944
2048 x 1536
1600 x 1200
1280 x 960
640 x 480
Printing larger than A4 size
Printing to postcard or attaching
to E-mail
Larger
Smaller
21
The resolution and quality will affect the required storage space of the images.
Compression Purpose
Super To shoot higher quality
images.
Fine To shoot normal quality
images.
Normal To shoot images.
Higher Quality
Lower Quality
Using the Zoom Function
Your camera has a digital zoom function that allows you to zoom in or zoom out on
subjects. The digital zoom enlarges or shrinks the image using a software process.
Make the zoom setting, and point
the camera at the subject.
Press
or on the five-way
control button (1) to compose the
image.
[W]: zoom out for a wide-angle
shot.
[T]: zoom in for a telephoto shot.
When the zoom button is
pressed, the zoom bar appears
on the LCD monitor.
Press the shutter button to take a
picture.
1
2
3
C
C
a
a
u
u
t
t
i
i
o
o
n
n
22
y The digital zoom works by enlarging the center portion of an image through a
software interpolation process.
y The digital zoom is used to achieve magnification levels up to approx. 4 times.
y The higher the digital zoom, the lower the image quality.
Using the Flash
The flash is not only for taking pictures when there is insufficient light, but also for when
the subject is in shade or with backlight conditions. Pressing the flash button cycles your
camera through the various flash modes. The flash will not activate during continuous
shooting or movie recording.
Turn the power on and set the camera
to the Capture mode (
page 13).
Press
on the five-way control
button (1) to change the flash mode.
y Each time the flash button is pressed,
the flash icon (2) changes.
Auto flash:
Flash fires automatically
when shooting conditions
require extra lighting.
Full Flash:
Flash fires every time you take a photo, regardless of lighting
conditions.
Flash OFF:
The flash never fires even in dark conditions.
Press shutter button to take a picture.
T
T
i
i
p
p
s
s
1
2
3
23
y The flash charging time may increase when the battery is low.
y The screen is blank when the flash is charging. The next image can be shot only
when charging is completed.
y Shooting with a flash in a bright environment may cause incorrect exposure.
Using the Selftimer
Use the selftimer to set a delay from the time the shutter button is pressed to the time
the image is shot. Use Burst to record continuous still image shooting.
Turn the power on, and set the camera to the Capture mode (
page 13).
Open the REC menu ( page 15).
Change the setting.
Press Mode button to launch the submenu. Press
or to select [Seftimer],
then press OK/Enter to confirm the setting.
Disable: Do not use Selftimer.
10 sec.:
The shutter release will delay for 10 seconds.
20 sec.
The shutter release will delay for 20 seconds.
Press the MENU button to close the menu list. Press the shutter button to
take a picture.
y When using the selftimer function, be sure to use a tripod or place the digital
camera on a level, stable surface.
y When using the selftimer function the selftimer lamp will blink and turn off after
the picture is taken.
C
C
a
a
u
u
t
t
i
i
o
o
n
n
4
T
T
i
i
p
p
s
s
1
2
3
24
Using the Burst-Snapshot
Use this function to take 3 pictures continuously.
Turn the power on, and set the camera to the Capture mode (
page 13).
Open the Capture menu (
page 15).
Change the setting
Press the Mode button to launch the submenu. Press
or on the five-way
control button to select [Burst-Snapshot]. then press OK/Enter to confirm the
setting.
Single: Press the shutter button once to take one picture.
Burst: Press the shutter button once to take three pictures continuously.
Press the MENU button to close the menu list.
Press the shutter button to take a picture series. When using the Burst-Snapshot
function the flash will not work.
4
1
2
3
25
Recording Movie Clips
Turn the power on, and set the camera to the Video mode (
page 13).
Compose the subject on the monitor.
y Point the center area of the LCD screen at the subject that you want to take.
Start recording.
y Press the shutter button to start recording.
y The LCD monitor displays the recorded time.
y The white balance is set and locked to the settings of the first frame.
Finish recording.
y Press the shutter button again to stop recording.
y The camera will stop recording automatically when the memory capacity is
full.
y When the digital zoom function is used in Movie mode the zoom bar will not
display.
Setting the Movie Size
Movie size and frame rate
Resolution Frame rate
640 x 480 30 fps / 15 fps
320 x 240 30 fps / 15fps
Higher quality
Lower quality
3
4
1
2
C
C
a
a
u
u
t
t
i
i
o
o
n
n
26
Recording Audio
Turn the power on, and set the
camera to the Audio mode
(
page 13).
Press the shutter button (1) to
start recording.
The voices are recorded via the
microphone (2) of the camera. Be
careful to avoid touching the
microphone while recording.
Press the shutter button again to end recording.
The camera will stop recording automatically when the memory capacity is full.
Please note that this camera has no built-in speaker. Sound is only available
when connecting with TV or PC to playback.
Playing Back Audio
Turn the power on, and set the camera to the Playback mode (
page
13).
Press
or on the five-way control button to select the audio file (WAV).
Start playback.
Press the shutter button to start playing the audio file. Press it again to stop the
audio file. Press OK/Enter to pause. When the audio playback is paused, press
OK/Enter to resume.
Please note that this camera has no built-in speaker. Sound is only available when
connecting with TV or PC to playback.
3
1
2
1
2
3
C
C
a
a
u
u
t
t
i
i
o
o
n
n
C
C
a
a
u
u
t
t
i
i
o
o
n
n
27
Other Recording Functions
Setting the White Balance
Adjust the white balance to suit different light sources such as sunlight, incandescent
(tungsten) lighting or fluorescent lighting.
Option Description
Automatically corrects white balance. Ideal for general
photography.
Adjusts for bright sunlight conditions or natural light conditions.
Adjusts for normal indoor lighting conditions. Corrects the
orange hue of household light bulbs. Ideal for indoor photos
under tungsten or halogen lighting without a flash.
Adjusts for fluorescent lighting. Corrects the green hue of
fluorescent lighting. Ideal for indoor photos under fluorescent
lighting.
Adjusts for cloudy days or twilight conditions.
y A practical method of obtaining the proper white balance is by comparing the
different white tones resulting from photographing a white sheet of paper with the
different manual White Balance settings. From the most realistic white tone
obtained you can determine the best White Balance setting under the current
lighting conditions.
T
T
i
i
p
p
s
s
28
Setting the Color Effect
Set the color effect to add a color tone to the picture.
Option Description
Color Reflects the true color of the object.
Sepia Adds a sepia color tone to the picture
Monochrome The pictures only have two colors: white and black.
Setting the Exposure
Set the exposure value manually to compensate for unusual lighting conditions such as
indirect indoor lighting, dark backgrounds, and strong backlighting.
Turn the power on, and set the
camera to the Capture mode
( page 13).
Open the Capture menu.
Press the MENU button (2) to
display the menu.
Select Exposure.
Press or on the five-way control button (1) to select [Exposure].
Change the setting.
Press on the five-way control button (1) to launch the submenu. Press or
on the five-way control button (1) to change the setting.
Apply the setting.
Press OK/Enter on the five-way control button (1) to apply the setting. Press the
MENU button to close the menu.
3
4
5
1
2
29
Setting Date Stamp
The date stamp function can be used to add a date to your pictures as you take them.
Option Description
Enable
Add the recording date & time to printed images.
Disable
Do not add the recording date & time to printed images.
30
Playback
Playing Back Images
Turn the power on, and set the camera to the Playback mode (
page
13).
The latest recorded image appears on the LCD display. If there are no images
stored, a message [No file] appears.
Pressing
or on the five-way control button displays the previous or next
image.
: displays the previous image.
: displays the next image.
Playing Back Movie Clips
Turn the power on and set the camera to the Playback mode (
page
13).
Press
or on the five-way control button to select a movie clip that you
want to play back.
Start playing back.
Press the shutter button to start playing the movie clip. Press the shutter button
again to stop the movie clip, or press OK/Enter to pause it. When the movie is
paused, press the five-way control button again to resume.
Please note that this camera has no built-in speaker. Sound is only available when
connecting with TV or PC to playback.
1
2
1
2
3
C
C
a
a
u
u
t
t
i
i
o
o
n
n
31
Using the Menu in Playback Mode
When a menu is displayed, the five-way control button is used to make the desired
settings.
Using the Menu in Playback Mode
Turn the power on and set the
camera to the Playback mode
( page 13).
Open the Playback menu.
Press the Menu button (2) to display
the menu.
Select an item.
Press or on the five-way control button (1) to select an item.
Change the setting.
Press
on the five-way control button (1) to launch the submenu. Press or
on the five-way control button (1) to change the setting.
Press OK/Enter (1) to save the settings and finally press the Menu button (2) to
close the menu.
If the item in the menu list is gray it means this item doesn’t work in this file format.
1
2
3
5
4
C
C
a
a
u
u
t
t
i
i
o
o
n
n
32
Viewing Thumbnails
Turn the power on and set the
camera to the Playback mode
(
page 13).
Press
on the five-way control
button: a thumbnail screen is
displayed. You can also view the
thumbnail screen in the following way:
Set the camera to the Playback mode,
then press the MENU button to display
the menu. Press
on the five-way
control button and select [Thumbnail].
Finally press
on the five-way
control button to view the thumbnail
screen.
Use
/ / / on the five-way control button to select the desired image,
and press OK/Enter to show the selected image in full screen.
You can delete images in thumbnail view see (
page 33)
Playing a Slide Show
Turn the power on, and set the camera to the Playback mode (
page 13).
Enter the slide show.
Press the MENU button. Press
/ on the five-way control button to select
[Slide show] then press
on the five-way control button to start the slide show.
End the slide show.
During the slideshow, press OK/Enter to pause and press it again to resume.
Press the shutter button to end the slide show
3
1
2
T
T
i
i
p
p
s
s
1
2
3
33
Deleting Files
Deleting a Single File
Turn the power on, and set the camera to the Playback mode (
page
13).
Select the file you want to delete.
When the file is shown in full screen, press
or on the five-way control
button to select the file you want to delete.
Open the menu.
Press the MENU button, then press
or on the five-way control button to
select [Delete current].
Delete the file.
Press
on the five-way control button to delete the file.
To quickly delete the current image:
1: Set the file shown in thumbnail mode.
2: Press
/ / / on the five-way control button to select the file you want to
delete.
3: Press the MENU button to display the dialog “Confirm delete? Yes/ No”.
4: Press
on the five-way control button to select “Yes” then press OK/Enter to
delete it.
T
T
i
i
p
p
s
s
1
2
3
4
34
Deleting All Files
Turn the power on, set the camera to Playback mode.
Open the menu
Press the MENU button. Then press
or on the five-way control button to
select [Delete all].
Delete the files
Press
on the five-way control button to delete the files.
All the files can be deleted except the protected files.
Formatting the SD Card or Internal Memory
Turn the power on and set the camera to any mode except Audio mode.
Open the menu.
Press the MENU button, then press
on the five-way control button to select
[Setup]. Now press
or on the five-way control button to select [Format].
Formatting the SD card or internal memory.
Press
on the five-way control button to launch the submenu.
Press
or on the five-way control button to select [Yes] and then press
OK/Enter to format .
Use this function to erase all data stored on the memory card if you are using a
card, or all data stored in the internal memory if there is no card inserted.
Be sure to backup all important files before formatting.
T
T
i
i
p
p
s
s
1
1
2
3
T
T
i
i
p
p
s
s
2
3
35
Protecting Files
Turn the power on and set the camera to the Playback mode
(
page 13).
Select a file to be protected. If you want to protect a single file select it before
operating the following steps. Press
or on the five-way control button to
select a recorded file
Open the menu.
Press the MENU button, then use the five-way control button to select [Lock].
Press
on the five-way control button to launch the submenu:
y [Lock current]: Protects a single file
y [Lock all]: Protects all files
y [Unlock current]: Unprotects the selected protected file
y [Unlock all]: Unprotects all the protected files
Select an item.
Press
or on the five-way control button to select an item.
Apply the setting.
Press OK/Enter to apply the setting.
Close the menu.
Press the MENU button to close the menu.
An icon will be displayed on protected files.
Protected files cannot be deleted; however if the SD card or internal memory are
formatted, the protected files will also be erased.
T
T
i
i
p
p
s
s
2
3
4
5
6
1
36
Choosing a Startup Image
Setting the Logo
Turn the power on, and set the camera to the Playback mode.
Select a still image as startup image.
Press
or on the five-way control button to select a still image.
Open the menu.
Press the MENU button, then use the five-way control button to select [Set Logo]
then press
on the five-way control button to launch the submenu: [Yes]; [No].
Apply the setting.
Press
or on the five-way control button to select [Yes] then press OK/Enter
to apply the setting.
Close the menu.
Press the MENU button to close the menu.
The startup image will not be deleted even if the original image is deleted or the
memory is formatted.
C
C
a
a
u
u
t
t
i
i
o
o
n
n
1
2
3
4
5
37
Editing Images
Rotating Still Images
Turn the power on, and set the camera to the Play mode (
page 13).
Press
or on the five-way control button to select the image you want to
rotate.
Open the menu.
Press the MENU button, then use the five-way control button to select [ Rotate]
and finally press
on the five-way control button to launch the submenu:
[90°]: Rotates the image 90 degrees clockwise
[180°]: Rotates the image 180 degrees clockwise
[270°]: Rotates the image 270 degrees clockwise
Select an item.
Press
or on the five-way control button to select the degrees.
Apply the setting.
Press OK/Enter to apply the setting.
Close the menu.
Press the MENU button to close the menu.
If the picture size is 5 megapixel or more the rotating function will not work.
1
2
3
4
5
6
C
C
a
a
u
u
t
t
i
i
o
o
n
n
38
Printing
The Digital Print setting allows you to directly print from a camera to a printer by
connecting them via a USB cable. Photos can be printed quickly and easily from your
digital camera without using a computer
Turn the power on, set the camera to the Playback mode and press
or
on the five-way control button to select a still image
(
page 13).
Open the menu.
Press the MENU button, then use the five-way control button to select [Print]
and then press
on the five-way control button to launch the submenu.
Select an item.
Press
or on the five-way control button to select [Yes].
Confirm the setting.
Press OK/Enter to apply the setting, then a message “Please connect to printer”
appears. Connect the camera to a compatible printer with the supplied USB
cable.
Power on the printer and press OK/Enter: the image is printed. For more
information please refer to your printer’s instructions.
4
5
2
1
3
39
Making Connections
Connecting the Camera to a TV
You can display recorded images on a television with the supplied AV cable.
Set the TV-out to match the TV system that you are using.
Turn off the camera and the TV.
Use the supplied AV cable to connect the camera to the TV set.
Then turn on the camera and the TV.
Set the TV input signal to Video In.
y Refer to the documentation included with your TV for more information.
Display on TV.
y Everything that would normally appear on the camera's LCD screen, such
as photos and video clip playback, slide shows and image or video capture,
will appear on the TV. The camera’s LCD screen turns off.
3
4
5
1
2
40
Connecting the Camera to a PC
There are two ways to download files from the camera's internal memory or memory
card to a computer:
By inserting the memory card into a card reader
By connecting the camera to a computer using the supplied USB cable.
Using a Card Reader (not included)
Eject the memory card from the camera and
insert it into a card reader that is connected to
a computer.
Open [My Computer] or [Windows Explorer]
and double-click the removable disk icon that
represents the memory card.
Copy images from the card into a directory of your choice on the computer’s
hard disk.
Connecting the Camera to a PC with the USB Cable
To download photos from the camera
Connect the supplied USB cable to the computer's USB port and turn on the
camera. A message “Mass Storage” or “PC Camera” appears on the screen
when connection to the computer has been successfully completed. Press the
playback button to switch the camera mode between mass storage and PC
camera. To download photos please select “Mass Storage” mode.
Open [My Computer] or [Windows Explorer]. A "Removable Disk" appears in the
drive list.
Double-click the "Removable Disk" icon to view its contents. Files stored on the
camera are located in the folder named "DCIM".
Copy the photos or files to your computer.
3
1
2
1
3
2
41
System Requirements
PC with processor better than MMX Pentium 233 MHz
Windows XP/ 2000/ Vista32
Minimum 32 MB RAM
USB port
CD-ROM drive
800 x 600 pixels, 16-bit color display compatible monitor
*Specifications are subject to change without prior notice.
42
Appendix
About the Folder & File Names
Your digital camera automatically creates a directory of folders in the internal memory or
on the memory card that it uses to organize still images, movie clips and other
information.
Folder Structure
The folder name begins with a 3-digit number from
100 to 999 and is followed by "DCIM". A new folder
can only be made manually. If new files are made,
the new files named in sequence will be made
automatically.
Naming Files
File names begin with "PICT" and are followed by a 4-digit number that increases in
sequence. File numbering starts from 0001 when a new folder is created.
y Do not change the folder and file names on the memory card using your
computer: it may be unable to play back the data on the digital camera.
C
C
a
a
u
u
t
t
i
i
o
o
n
n
43
Troubleshooting
Problem Cause Solution
Batteries are inserted in the
wrong direction.
Reload batteries in the correct
direction.
Batteries are dead. Replace or recharge batteries.
Power does not turn camera
on.
The battery compartment door
is open.
Make sure the battery
compartment door is securely
closed.
The flash is charging. Wait for the flash to charge.
Memory is full. Insert a new memory card.
The camera does not take
pictures.
Memory card is not formatted
correctly.
The card may be defective:
use a new card.
The flash is charging. Wait for the flash to charge. Image is not recorded when
the shutter button is pressed.
Memory is full. Insert a new memory card.
The flash does not fire. Flash is set to OFF. Set the flash to any mode
except off.
The image is blurred or out of
focus.
The camera was moving when
the image was captured.
Hold the camera steady when
shooting a picture.
The image is not displayed on
the LCD monitor.
A memory card with
non-PICT images (recorded
with another camera) is
loaded.
This camera cannot display
non-PICT images.
Recorded images are not
saved in memory.
The camera was turned
off/powered down before
saving images to the
memory.
If the battery low indicator
appears on the LCD monitor,
replace the battery
immediately.
44
Specifications
AgfaPhoto
sensor 505-D
AgfaPhoto
sensor 510-D
AgfaPhoto
sensor 500-D
Sensor
5 MegaPixel CMOS,
Size: 1/2.5 inch
5 MegaPixel CMOS,
Size: 1/2.5 inch
3 MegaPixel CMOS,
Size: 1/2.5 inch
Display
2.4" TFT color LCD 2.4" TFT color LCD 2.0" TFT color LCD
Focus range
150cm ~ infinity 150cm ~ infinity 150cm ~ infinity
Aperture
F3.1, Fixed focus F3.1, Fixed focus F3.1, Fixed focus
Shutter
Electronic shutter:
1/2,000 ~ 1/14 sec.
Electronic shutter:
1/2,000 ~ 1/14 sec.
Electronic shutter:
1/2,000 ~ 1/14 sec.
File format
Still Image: JPEG (EXIF
2.2 compatible)
Video: AVI
Audio: WAV
Still Image: JPEG (EXIF
2.2 compatible)
Video: AVI
Audio: WAV
Still Image: JPEG (EXIF
2.2 compatible)
Video: AVI
Audio: WAV
Resolution
Still Image:
2592 x 1944; 2048 x
1536; 1600 x 1200;
1280 x 960; 640 x 480
Video:
640 x 480, 320 x 240
Still Image:
8 MP interpolation
3264 x 2448; 2592 x
1944; 2048 x 1536;
1600 x 1200; 640 x 480
Video:
640 x 480, 320 x 240
Still Image:
5 MP interpolation
2592 x 1944; 2048 x
1536; 1600 x 1200;
1280 x 960; 640 x 480
Video:
640 x 480, 320 x 240
Sensitivity
Auto Auto Auto
White balance
Auto, Daylight,
Tungsten, Fluorescent,
Cloudy
Auto, Daylight,
Tungsten, Fluorescent,
Cloudy
Auto, Daylight,
Tungsten, Fluorescent,
Cloudy
Exposure control
-2EV to +2EV in 1/3 -2EV to +2EV in 1/3 -2EV to +2EV in 1/3
45
steps steps steps
Burst
Included Included Included
Flash
Auto, Always on, Always
off
Auto, Always on, Always
off
Auto, Always on, Always
off
Photo effect
Color, Sepia,
Monochrome
Color, Sepia,
Monochrome
Color, Sepia,
Monochrome
Selftimer
Disable / 10 / 20 sec. Disable / 10 / 20 sec. Disable / 10 / 20 sec.
Storage
32 MB internal memory
External memory:
SD (2 GB)
32 MB internal memory
External memory:
SD (2 GB)
32 MB internal memory
External memory:
SD (2 GB)
TV system
NTSC / PAL NTSC / PAL NTSC / PAL
Power supply
AAA rechargeable
battery x 2 (optional);
AAA alkaline battery x 2
AAA rechargeable
battery x 2 (optional);
AAA alkaline battery x 2
AAA rechargeable
battery x 2 (optional);
AAA alkaline battery x 2
Environmental
temperature
Operating: 0° C to 40° C
Storage: -20 to 60° C
Operating: 0° C to 40° C
Storage: -20 to 60° C
Operating: 0° C to 40° C
Storage: -20 to 60° C
Microphone
Built-in Built-in Built-in
Speaker
Not included Not included Not included
Dimension camera
body (W x H x D):
100x 59.4 x 26.6mm 100x 59.4 x 26.6mm 100x 59.4 x 26.6mm
Weight (w/o battery)
Approx. 85 (g) Approx. 85 (g) Approx. 85 (g)
*These specifications are subject to change without prior notice.
46
Customer care
More information on the complete AgfaPhoto digital camera product range can be found
under www.plawa.com / www.plawausa.com
Service & Repair (USA / Canada):
1-866 475 2605
www.plawausa.com – live chat available
Support Service (USA / Canada):
support-apdc@plawausa.com
Online Service USA / Canada:
support-apdc@plawausa.com
Service & Repair Hotline (Europe):
00800 752 921 00 (from a landline only)
Service & Support Hotline (Germany):
0900 1000 042 (1.49 Euro/ min. from a German landline only)
Online Service / International contact (Not USA / Canada):
support-apdc@plawa.com
Designed and manufactured by
plawa-feinwerktechnik GmbH & Co. KG
Bleichereistraße 18
73066 Uhingen
Germany
AgfaPhoto is used under license of Agfa-Gevaert NV & Co. KG. Agfa-Gevaert NV & Co.
KG. does not manufacture this product or provide any product warranty or support. For
service, support and warranty information, contact the distributor or manufacturer.
Contact: AgfaPhoto Holding GmbH, www.agfaphoto.com
47
Disposal of Waste Equipment by Users in Private Households in
the European Union
This symbol on the product or on its packaging indicates that this product must not be
disposed of with your other household waste. Instead, it is your responsibility to dispose
of your waste equipment by handing it over to a designated collection point for the
recycling of waste electrical and electronic equipment. The separate collection and
recycling of your waste equipment at the time of disposal will help to conserve natural
resources and ensure that it is recycled in a manner that protects human health and the
environment. For more information about where you can drop off your waste equipment
for recycling, please contact your local city office, your household waste disposal service
or the shop where you purchased the product.
FCC Compliance and Advisory
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: 1.) this device may not cause harmful interference, and 2.) this device
must accept any interference received, including interference that may cause
unsatisfactory operation. This equipment has been tested and found to comply with the
limits for a Class B peripheral, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communication. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the
following measures.
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment to an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
48
Any changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment. When shielded
interface cables have been provided with the product or when specified additional
components or accessories have elsewhere been designated to be used with the
installation of the product, they must be used in order to ensure compliance with FCC
regulations.
19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Agfaphoto sensor 505-D wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Agfaphoto sensor 505-D

Agfaphoto sensor 505-D Bedienungsanleitung - Deutsch - 50 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info