Bedienungsanleitung Ahrend 500 (Seite 27 von 74) (Deutsch, Englisch, Holländisch, Französisch, Spanisch)

554590

Zoom out

Zoom in

Vorherige Seite

1/74

Nächste Seite

1 2

3 4

Table height

A range of leg models

Ahrend 500 tables are available as fixed height

models or in three height-adjustable versions.

You can see the difference in the vertical part of

the table legs (figs. 1 to 8).

Fixed table height

Afixed height Ahrend 500 table (figs. 1and 2)

is ideal for the great majority of users engaged in

normal office work and for meeting and conference

tables.

Afixed height of 72 cm is correct for people

who are between about 1.60 and 1.75 m tall

(5ft 3ins to 5ft 9ins).

Afixed height of 74 cm is correct for people

who are between about 1.65 and 1.80 m tall

(5ft 5ins to 5ft 11ins).

Shorter people are advised to use afootrest;

taller people should have aheight-adjustable table.

Height-adjustable tables (HI)

Aheight-adjustable Ahrend 500 table (figs. 3

and 4) can be adjusted to suit your personal

requirements. The height can be adjusted from

62 to 90 cm. As a rule the table will be adjusted only

once, by the user of the workstation.

Variable height tables (HV)

A variable height Ahrend500 table (figs. 5and 6)lets

you adjust theheight of the work surface mechanically

to suit your own height and posture at any time. This

means that different people can use the same work

table at different times in maximum comfort.

By turning the handle the height can be adjusted from

62 to 90 cm.

Working out the correct table

height

Sit on a table in a relaxed manner

with the backs of your knees

against the edge of the table.

Three important dimensions can

now be measured:

Dimension A: the distance from the

bottom of the heel of the shoe to

the top of the table.

Dimension B: the distance from the

top of the table to the underside of

the elbow, sitting upright, with the

arm alongside the body and bent at

an angle of 90º.

Dimension C: the distance between

the top of the table and a ruler

placed across the thighs, plus 5 cm. If

this is greater than dimension B, you

should use dimension Cinstead of

dimension B.

The right work surface height for

you is the sum of dimensions A

and B(or A and C) rounded off to

the nearest even number.

Height adjustment (HI)

C-leg (fig.3):Remove the round

cap from the leg (hold it and pull

it loose by pulling it diagonally

downwards).

Note:The push-button is sometimes

located on the inside of the leg,

above the round bar.In that case

do not remove the cap.

English

Keep the base of the leg in place

with your foot. Press and hold the

push-button while extending or

retracting the upper section of the

table to set the required height.

Now release the push-button and

move the table a little until the

push-button springs back into its

original position and the leg snaps

into place. Fit back the cap.

When adjusting corner legs follow

the same procedure as with N-legs.

050099Ahen500 19-10-2005 15:20 Pagina 2

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ahrend 500 Seite 27

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info