Bedienungsanleitung Aidapt VA172HAM (Seite 7 von 8) (Englisch)

779093

Zoom out

Zoom in

Vorherige Seite

1/8

Nächste Seite

1. Backrest

The adjustable backrest can be folded down by means of a locking mechanism tted to

both sides of the lower part of the backrest pillars. To fold the backrest down, push on

both of the black plastic levers, then pull back and down on the top part of the backrest. To

return to the original, reverse the procedure, making sure the mechanisms are locked securely.

2. Handles

The handles are designed for the helper to propel the chair. They must not be used solely

for lifting the chair over obstructions or kerbs (see negotiating obstacles)

The helper must not place all of their weight on the handles by lifting their feet o the

oor as this will place adverse strain on the handles.

3. Armrest

PVC pads are xed onto the armrest for comfort and can be replaced as spare parts.

4. Seat Upholstery

Periodically check the upholstery for signs of tears or sagging. Replace immediately if the

seat is damaged. Remember: the seat upholstery is the primary weight supporting material.

5. Footplates

The footplates are intended as a foot support only when you are sitting in the chair. On no

account should you stand on the footplates. The heel loops or calf straps (if tted) can be

used to secure the position of the feet. The footplate assemblies can be adjusted in height by

loosening the nut of the base of the adjustment tube, positioning the plate at the required

height and tightening the nut to secure the assembly. The footplate supports can be swung

away to the outside of the chair. To carry out this procedure, pull the release lever towards the

front and swing the support to the outside of the chair. If the support is to be removed, lift it

upwards. To re-t and return to the original position, reverse the above procedure.

6. Castor and bearing

The front and rear wheels are solid puncture proof tyres. These should be checked at

regular intervals to monitor any wear. Chairs become dicult to steer and propel when

surfaces have worn at. It is recommended that both front tyres are replaced at the same

time to avoid one side of the chair from being higher than the other.

The wheel is secured to the castor fork by an axle bolt and axle nut. Periodically, this bolt

and nut should be checked and tightened if necessary to allow a snug but free spinning t.

The castor fork swivel on the front wheels allow the chair to be steered in either left or right

direction. An adjustment locknut is located under the castor cap. If the locknut is too tight,

the chair will be dicult to steer.

7. Wheel lock assembly

These are used to hold the chair in a stationary position, and are tted on either side of the

chair on the back wheels. They should not be used when the chair is moving or to slow it

down. They should always be applied together.

To operate, pull the brake lever back towards the back of the chair. This will immobilize the

chair. To release the brake, move the lever forwards the front of the chair.

8. Cross Bar

Operation of the cross brace permits the chair to be opened and closed easily. It should be

inspected at regular intervals for signs of wear and bending.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Aidapt VA172HAM Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info