Bedienungsanleitung Aigger HSM5657A (Seite 29 von 78) (Deutsch, Englisch, Holländisch, Französisch)

560624

Zoom out

Zoom in

Vorherige Seite

1/78

Nächste Seite

Button for sewing backwards (illustration 15)

Push the button down to sew backwards. The material is then automatically transported

backwards. You can use this function to strengthen the sewing.

Stitch selection button (illustration 16)

Ensure the needle is in the highest position. This is done by turning the fly-wheel. Turn the

selection button to the required stitch.

Once you have set the stitch length between 0 and 4, you can choose between 10 different

stitches, which will have the same colours as the 0-4 numbers of the stitch length.

Once you have set the stitch length button to SS, you can sew stretched stitches by way of

selecting the stitches with the same colour as the SS symbol (A-J).

Exchanging the bobbin

1 Bring the needle to the highest position

2 Bring the pressure foot up by lifting the pressure foot lever upwards. (illustration 17)

3 Then open the protecting cover of the bobbin housing. (illustration 18)

4 Open the lock of the bobbin housing and then take the bobbin housing out of the machine

together with the bobbin. (illustration 19)

5 Hold the bobbin housing with one hand and remove the bobbin with your other hand.

(illustration 20)

6 Insert a new bobbin. (illustration 21)

7 Put the thread in as indicated in the picture. (illustration 22)

8 You can now place back the bobbin housing by keeping the lock open and pushing it

inwards over its pin. (illustration 23)

9 See that approximately 15cm of thread sticks out of the bobbin. (illustration 24)

Winding bobbins

1 Turn the motor interlocking loose by turning the button towards yourself.

(illustration 25 and 26)

2 Thread the yarn in as is indicated in the picture. (illustration 27)

3 Pull the end of the thread through the hole in the bobbin as indicated in the picture.

(illustration 28)

4 Place the bobbin on the bobbin winder and move this to the right until it clicks. When the

bobbin has been wound a little bit, you remove the thread end. (illustration 29)

5 You can now continue winding, until the bobbin winder stops automatically.

(illustration 30)

6 Turn the motor interlocking to the right position. (illustration 31)

Threading the thread (illustration 32)

1 Place the top thread spool on to the holder that is there for this purpose. Turn the needle

to the highest position so that guide 4 becomes visible. Lift the pressure foot holder up by

moving the pressure foot holder upwards.

2 Then thread the yarn along the guides 1 and 2.

3 Lead it via the tension control 3 to guide 4, to thread guide number 5.

4 Then lead the thread via thread guide number 6 to the needle and put the thread through

the needle from front to back.

Bringing the bobbin thread up (illustration 33)

1 When you have threaded the upper thread through the needle you can bring the bobbin

thread up by turning the flywheel towards yourself. Turn so far until the needle has made an

upward movement in once and the needle is again in its highest position.

Nederlands

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Aigger HSM5657A Seite 29

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info