Bedienungsanleitung Aigger HSM5657A (Seite 37 von 78) (Deutsch, Englisch, Holländisch, Französisch)

560624

Zoom out

Zoom in

Vorherige Seite

1/78

Nächste Seite

1 Place the blind hemming foot, as is described on page 29.

2 Guide the material properly through the foot as is shown in the picture.

3 You can use the adjusting screw to set the right hem width. (illustration 53)

Free arm machine (illustration 54)

This machine disposes of a free arm. By removing the arm you can turn this machine into a

free-arm machine, which makes it easier to work on tubular pieces, such as trouser-legs and

sleeves.

Slide the part that you want to sew on to the arm and sew from the top. When you have

finished sewing with the free arm, you put the arm in its place again.

THE MAINTAINANCE

Cleaning the bobbin housing (illustration 55)

1 Set the on / off switch to "O" (OFF).

2 Remove the power cable from the sewing machine and take the plug out of the wall socket.

3 Bring the needle to the highest position.

4 Remove the bobbin housing (see page 31 bobbin replacement).

5 Turn the position finger outwards and remove the safety ring.

6 Remove the hook by taking it in the middle and pulling the whole outwards.

7 Remove any dust and thread from the safety ring, hook, drive and grab track with a brush.

8 With a cloth that you have moistened with sewing machine oil, dust and other rests can be

removed from the grab track.

9 Clean the bobbin housing.

10 Mount the hook again with the notch at the top and push the position fingers back into the

right position to keep the safety ring in its place.

WARNING When exchanging the light bulb, remove the plug from the wall socket. To prevent

burns, you must be extremely careful when exchanging the light bulb. Light bulbs are available

from the sewing machine specialist shop. Use a 15W light bulb. If you use a light bulb with a

higher wattage the guarantee expires.

Cleaning the transporter

1 Set the on / off switch to "O" (OFF).

2 Remove the power cable from the sewing machine and take the plug out of the wall socket.

3 Remove the screw on the left-hand side of the needle plate with the screw driver. Remove

the needle plate.

4 Clean the transporter with a brush.

5 Place the needle plate back in its place.(illustration 56 and 57)

Oiling the machine (illustration 58)

The arrows in the picture show which points in the machine must be oiled. Before you apply

the oil, these spots must be cleaned. Apply one or two drops of sewing machine oil of a good

quality. Should the machine not function properly after it has not been used for a long time,

you must apply a few drops of oil at the marked spots. Then you allow the machine to run fast

for a few minutes with all the lids closed. Sewing machine oil is available at the sewing

machine specialist shop.

WARNING! Do not forget after oiling the machine to sew on a piece of waste material first, to

catch any superfluous sewing machine oil.

English

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Aigger HSM5657A Seite 37

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info