Bedienungsanleitung Air and Me Solnan (Seite 9 von 49) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

807103

Zoom out

Zoom in

Vorherige Seite

1/49

Nächste Seite

MAIN FUNCTIONS

• Make sure the unit is turned off and unplugged before handling.

• Do not immerse the device in water or any other liquid.

• Do not use corrosive, abrasive or flammable products to clean the unit.

CLEANING THE TANK: To avoid scale deposits, clean the tank at least once a month with a

suitable product or white vinegar. To do this, remove the tank from the unit and remove the

cap, then ll it with water and cleaning agent. Let stand for 15 minutes, then empty and rinse

the tank thoroughly with clean water before putting it back in place and turning on the device

again.

CLEANING ULTRASONIC PLATE : Dry the ultrasonic plate and clean it with a soft brush. Then wipe

it with a soft cloth.

STOCKAGE: To avoid any bacteria or virus proliferation, never store the appliance with water

inside the tank and be sure that the appliance is perfectly dry. Never leave water in the tank

when the unit is not used.

1. Empty and clean the tank.

2. Clean the pre-lter.

3. Store the product in a place that is protected against dust and that is clean and dry.

AUTOMATIC AIR HUMIDIFICATION

C [POWER] FUNCTION: SOLNAN is equipped with 3 levels of diffusion power, allowing to in-

crease the speed of air humidification and to regulate the intensity of the mist. The corres-

ponding number appears on the digital display:

1 – Low power

2 – Medium power

3 – High power

When the digital display indicates the ambient humidity rate, press it once to increase the

preset power. Press it a second time to change the power.

At full power, the mist produced may condense around the appliance and give the impres-

sion of a tank leak. To avoid this phenomenon, reduce the diffusion power and/or place the

humidifier towards a heat source (at about 1 meter).

B [TIMER] FUNCTION: This function allows you to choose the operating time of your appliance,

from 1 to 12 hours.

1. By pressing button B, the digital display indicates “01” for “1 hour of operation”. Press the

button repeatedly to reach the desired value.

2. Without any action on your side, the digital timer display stops flashing after 5 seconds,

which means that the setting is successful.

3. Once the desired operating time is set up, the digital display indicates the remaining time

every minute, and decreases from hour to hour. If you have set the Timer to “03" (3 hours),

the digital display will indicate “02" after one hour of operation.

To cancel the Timer setting, hold down button B for 2 seconds.

D [HYGROSTAT] FUNCTION: This function allows you to set up the ambient humidity rate to the

value you want (between 30 and 90%). For maximum comfort, we recommend a humidity

rate between 45 and 55%.

1. Before pressing button D, the digital display indicates the ambient humidity rate.

2. Press button D, several times to select the value you want. The value increases in steps

of 5%.

3. Without any action on your side, the digital hygrostat display stops flashing after 5 se-

conds, which means that the setting is successful.

4. Once the desired humidity rate is set up, the digital display indicates this rate every mi-

nute, flashing slowly.

Set up of the appliance in CONTINUOUS mode:

To activate this function, press several times the button D until the “CO” acronym appears.

After 5 seconds, the digital display indicates again the ambient humidity rate.

Caution: By selecting the [HYGROSTAT] function, it is not possible to adjust the power of the

appliance.

MAINTENANCE

SOLNAN is equipped with an [HYGROSTAT] function that allows you to choose a desired humi-

dity rate in your room. By making this setting, the appliance will automate its operating.

Desired humidity rate according

to the ambient humidity rate Automatic humidication power

Higher than 16% or more 3 – High power

Higher than 10 to 15% 2 – Medium power

Higher than 1 to 9% 1 – Low power

Lower The appliance is in standby

NIGHT MODE: You can activate or deactivate the LED display of the appliance:

1. Hold down the button D for 2 seconds: the blue LED situated under the appliance and the

digital display turn off.

2. Press one of the buttons to reactivate the digital display.

3. Press again one of the buttons to modify the operating mode of the appliance.

4. Hold down the button D again to reactivate the LED lights.

16 17

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Air and Me Solnan Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info