Bedienungsanleitung Airpress 36821 (Seite 36 von 56) (Deutsch, Englisch, Holländisch, Französisch)

594049

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

SW1 ON position - it enables the automatic re-start of the compressor in case of

power failure

OFF position - the compressor re-starts only by pressing the START key

SW2 ON position - the compressor re-starts after 3 minutes of low pressure

OFF position - the compressor re-starts after 1 minute of low pressure

SW3 ON position - delayed stop. Press the STOP key: the compressor stops

when the line pressure value is reached. The stop cycle is signalled by the

flashing red led OFF. This function is useful to avoid the risk of the

compressor re-start with the head under pressure. In such case, when

reaching the line pressure value is achieved, the exceeding air is blown off.

OFF position - Immediate stop af ter pressing the STOP key.

Recommended only when the compressor head is equipped with blowing off

valve.

SW4 SW4 switch is in position OFF at the delivery of the compressor.

DO NOT CHANGE THIS SETTING, IN ANV CASE, but, if necessary contact

an Authorized Service Centre.

6. OPERATION AND USE

6.1 Mode of Operation (Tandem models) (Fig. 7)

In order to select the operation cycle, press the STOP button for at least 4 seconds to

activate the different programmes (the corresponding green led wil I light up) at an

interval of 1/2 second. After selecting the desired programme, release the STOP

button. The selected programme will be kept stored in the memory even in case of

power failure.

• Cycle M1-M2: alternated operation of the two pumping units.

SW2 function is active only when this mode is selected, so, depending on your air

consumption, adjust the switch in position ON (Iow consumption) or OFF (high

consumption). When the line pressure value is reached, both the pumping units

stop, then they start again when the pressure value decreases.

• Cycle M1: operation of the sole pumping unit M1.

• Cycle M2: operation of the sole pumping unit M2.

NOTE: If just one unit is used, as usually happens, do not use always the same

unit but Iet the work be shared fairly by both of them.

• Cycle M1+M2: simultaneous operation of the two pumping units.

The first unit M1 starts and after about 10 seconds starts the unit M2; they both

work together and stop when the line pressure value is reached, then they start

again when the pressure value decreases.

NOTE: Please remember to start both units together only if a big amount of

compressed air is needed because under these conditions, and especially at

the start-up, high electrical input peaks may occur.

For the most appropriate operation cycle, contact your usual installer, taking into

account your compressed air consumption and the data written on the EG label of the

compressor.

6.2 Operation cycle

The compressor runs completely automatically by the pressure switch, which stops the

compressor when the max. pressure value is reached and restarts the compressor

only when this value has decreased to the minimum value accepted.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Airpress 36821 Seite 36

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info