Bedienungsanleitung Airwell Multisplit YAZE CINCO DCI (Seite 10 von 19) (Englisch)

590226

Zoom out

Zoom in

Vorherige Seite

1/19

Nächste Seite

PIPES CONNECTION

AND FLARRING THE PIPES

PIPE INSULATION

PIPES CONNECTIONS TO THE UNIT

EVACUATION OF PIPES AND INDOOR UNIT

Please use the pipe cutter for cutting the pipes.1.

Remove all burrs by using reamer. Gas leakage might 2.

happen If burrs are not removed! Turn pipes edge

down to avoid metal powder from entering down the

pipes.

After inserting the flare nut into the cooper pipes, 3.

please make a flare.

0.0-0.5mm

Bar

Coppet pipe

Reamer

To cut

Inclined

Surface

damaged

Cracked

Uneven

thickness

Please carry out insulation at pipe connection portion 1.

as mentioned in Indoor/ Outdoor Unit Installation

Diagram. Please wrap the insulated piping end to

prevent water from going inside the piping.

If drain hose or connecting pipes is in the room (where 2.

dew may form). Please increase the insulation by using

POLY-E FOAM with thickness of 9 mm or more.

Vinyl tape

Connecting to the indoor unit

Align the center of the pipes and finger tight the flare 1.

nut.

Use the torque wranch to tighten the nut firmely.2.

Connecting to the outdoor unit

Align the center of the pipes to the valves.1.

Use the torque wranch to tighten the valves firmely 2.

according to table:

Flare Nuts

Valve Cap

Service Port Cap

1/4

13-18

13-20

11-13

TUBE (Inch)

Torque(

N.m

)

3/8

40-45

13-20

11-13

1/2

60-65

18-25

11-13

5/8

70-75

18-25

11-13

3/4

80-85

40-50

11-13

After connection the unions of the indoor and outdoor units,

evacuate the air from the tubes and from the indoor unit is

follow:

Connect the charging hoses with a push pin to the low and high 1.

sides of the charging set and the service port of the suction and

liquid valves. Be sure to connect the end of the charging hose

with the push pin to the service port.

Connect the center hose of the charging set to a vacuum pump.2.

Turn on the power switch of the vacuum pump and make sure 3.

that the needle in the gauge moves from 0MPa (0cm Hg) to - 0.1

MPa (-76cm Hg). Let the pump run for fifteen minutes.

Close the valves of both the low and high sides of the charging 4.

set and turn off the vacuum pump. Note that the needle in the

gauge should not move after approximattely five minutes.

Disconnect the charging hose from the vacuum pump and from 5.

the service ports of the suction and liquid valves.

Tighten the service port caps from both valves, and open them 6.

using a hexagonal Allen wrench.

Remove the valve caps from both valves, and open them using 7.

a hexagonal Allen wrench.

Remount valve caps onto both of the valves.8.

Check for gas leaks from the four unions and from the valve caps. 9.

Test with electronic leak detector or with a sponge immersed in

soapy water for bubbles.

1. Charging set

2. Vacuum pump

3. OUTDOOR UNIT

4. Service valve

5. Cap

6. Suction valve

7. Service valve*

8. Cap

9. Liquid valve

10. INDOOR UNIT

11. Suction flare connection

12. Liquid flare connection

11 12

NOTE: For additional charge of various tubing

lengths, refer to outdoor unit table.

Sample





CUTTING

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Airwell Multisplit YAZE CINCO DCI Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info