Bedienungsanleitung Aiwa NSX-332 (Seite 50 von 60) (Englisch, Französisch, Spanisch)

496518

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

If the unit fails to perform as it is supposed to, by following this operation manual, please check it carefully in accordance with the chart below:

‘“*C There is no sound.

, q?

● The power cord is not connected properly.

Ill

● An incorrect function selector button is pressed.

&&Bf,

m,.

~~h-

● There is a bad connection between systems.

Ml,&

~.m s

● Excessive voltage was applied to a speaker jack,

.; *

which tripped the amplifier’s voltage-protection

breaker.

There is no sound and no

● There is a shorl circuit in the speaker jack.

~a indicators are lit in the display

● The breaker tripped because of connection to a low-

impedance speaker.

##l Sound comes from only one

● Onespeakeris disconnected.

constant, wavelike static, I

● The antenna is not connected properly.

U!M

I * The receiver is not correctlv tuned.

* The signal is too weak. -

c The system picks up outside noise.

The soun”d is distorted.

= There is multipath distortion.

~sl The tape does not run.

● Deck 2 is on pause.

‘“? The sound is off-balance.

● The playback head is dirty.

,##” High sounds are too loud.

● The DOLBY NR mode is set differently from when

M%{

I the recordina was done

*-&j

;; There are no high sounds.

● A non-Dolby NR tape is being played back in that

mode.

~(~g

I “ The Edavback head is dirtv.

Recording is impossible.

* The erasure-prevention tab on the tape has been

I broken.

~~q

I ● There is an incorrect connection.

~~f I ● The recording head is dirty.

Erasure is impossible.

● The erasure head is dirty.

● The disc is incorrectly inserted.

Rmm

]

● The disc is dirty.

Bma

‘!

& j

. There is condensation on the disc.

,Z,

● The player is on pause.

/,,,,,.

&& The output sound is not stereo.

● The VOCAL FADER is turned on,

● Correct the connection.

● Press the function selector button to select the

correct input.

● Correct the connection.

● Disconnect the power cord, correct the condition,

including speaker connections, and connect the

power cord again.

. Disconnect the power cord, correct the condition,

including speaker connections, and connect the

power cord a~ain.

● Correct the speaker connection.

● Check the antenna connection.

● Correct the tuning.

● Install an outside antenna,

● Change the location or direction of the antenna.

● Turn the system to a different orientation.

● Move the system away from other electrical

appliances, like a TV or fluorescent lights, or move

the appliances.

● Change the orientation of the antenna.

● Replace the antenna with one that has the correct

orientation.

● Press 11and release t)ause.

● Clean the head.

● Reset DOLBY NR to the same setting as when the

recording was made.

● Turn off DOLBY NR.

● Clean the head.

c Cover the erasure-prevention hole well with tape.

● Correct the connection.

● Clean the head.

● Clean the erasure head.

● Insert the disc with the label facina uo

● Clean the disc.

● Wait about an hour and try again.

● Press 11PAUSE to release ~ause.

● Turn off the VOCAL FADER.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Aiwa NSX-332 Seite 50

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info