Bedienungsanleitung Aiwa NSX-A31 (Seite 10 von 76) (Englisch, Französisch, Spanisch)

496499

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

,’

MANUAL TUNING

BAND

SHIFT

*i-------

—

1 Press the TUNER/BAND button repeatedly to

select the desired band.

FM — AM

When the TUNER/BAND button is pressed while the power

is off, the power is turned on directly.

To select a band with the remote control

Press the BAND button while pressing the SHIFT button.

2 Press the+ DOWN or FD UP button to setect

a station.

Each time the button is pressed, the frequency changes.

When a station is received, “TUNE” is displayed for 2 seconds.

During FM stereo reception; [il~ll) is displayed.

To search for a station quickly (Auto Search)

Keep the + DOWN or > UP button pressed until the tuner

starts searching for a station. After tuning in to a station, the

search stops.

To stop the Auto Search manually, press the * DOWN or FF

UP button.

● The Auto Search may not stop at stations with very weak

signals,

When an FM stereo broadcast contains noise

Press the MONO TUNER button while pressing the SHIFT button

on the remote control so that “MONO” appears on the display.

Noise is reduced, although reception is monaural.

To restore stereo reception, press these buttons so that MONO

disappears.

To change the AM tuning interval

The default setting of the AM tuning interval is 10 kHz/step. If

you use this unit in an area where the frequency allocation system

is 9 kHz/step, change the tuning interval. -

Press the POWER button while pressing the TUNEWBAND

button.

To reset the interval, repeat this procedure.

When the AM tuning interval is changed, all preset stations are

cleared. The preset stations have to be set again.

9 ENGLISH

PRESETTING STATIONS

0-9,+1 o

The unit can store a total of 32 preset stations. (Each band has a

maximum of 20 available preset stations. ) When a station is

stored, a preset number is assigned to the station. Use the preset

number to tune in to a preset station directly.,

7 Press the TUNEFVBAND button to select a band,

and press the ++ DOWN or F- UP button to

select a station.

2 Press the II SET button to store the station.

A station is assigned a preset number, beginning from 1 in

consecutive order for each band.

Frequency

Preset number

3 Repeat

steps 1 and 2.

The next statiorrwill not be stored if a total of 32 preset stations

for all the bands or a total of 20 preset stations for one band

have already been stored.

PRESET NUMBER TUNING

Use the remote control to select the preset number directly.

7 Press the BAND button while pressing the SHIFT

button to select a band.

2 Press the numbered buttons to select a preset

number.

Example:

To select preset number 20, press the +10, +10 and O buttons.

To select preset number 15, press the +1 O and 5 buttons.

Selecting a preset’number on the main unit

Press the TUNER/BAND button to select a band. Then, press

the ~ PRESET button repeatedly.

Each time the button is pressed, the next ascending number is

selected.

To clear a preset station

Select the preset number of the station to be cleared. Then, press

the

■ CLEAR button, and press the II SET button within 4

seconds.

The preset numbers of all other stations in the band with higher

numbers are also decreased by one.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Aiwa NSX-A31 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info