Bedienungsanleitung Aiwa NSX-D9 (Seite 20 von 92) (Englisch, Französisch, Spanisch)

496554

Zoom out

Zoom in

Vorherige Seite

1/92

Nächste Seite

This section explains how to record from the tuner, CD player,

or external equipment.

Preparation

● Set the tape to the point where recording will start.

● Use Type I (normal) and Type II (high/CrOz) tapes for recording.

Insert the tape to be recorded on into deck 2.

Insert the tape with the side to be recorded on first facing out

from the unit.

— = PUSH EJECT

Press REV MODE(DECK 2) to select the reverse

mode.

To record on one side only, select =.

To record on both sides, select =) or C=).

Press DOLBY NR to turn Dolby NR on or off.

To record with DOLBY NR, turn on 00 NR.

To record without DOLBY NR, turn off DO NR.

Press function (CD, TUNER/BAND, VIDEO/AUX or

MD) and prepare the source to be recorded.

To record from a CD, press CD and load the disc(s).

To record from a radio broadcast, press TUNEWBAND and

tune in to a station.

To record from a connected source, press VIDEO/AUX or

MD.

Press ● REC/REC MUTE to start recording.

When recording from a connected source, start playback of

the source.

When the selected function is CD, playback and recording

start simultaneously.

19 ENGLISH

To stop recording, press ■.

To pause recording, press II. (Applicable when the source is

TUNEWBAND, VIDEO/AUX or MD.) To resume recording, press

again.

To start recording with the remote control

First press

●

/0 REC/ REC MUTE, and then press +> within

2 seconds.

The output volume of the speakers or headphones maybe freely

varied without affecting the level of the recording. But BBE and

Rhythm play function (BEAT, AUTO SPICE/FILL IN, SPICEA/B)

will affect the recording.

Recording with BBE

The desired source can be recorded with the BBE function to

enhance the clarity of high-frequency sound, When playing back

a tape recorded with BBE, it is recommended that BBE be set to

off.

——t

TNSERTING BLAFK=S

Insertion of 4-second blank spaces enables you to activate the

Music Sensor function. (Applicable when the source is TUNER,

VIDEO/AUX or MD.)

1 Press

● REC/REC MUTE during recording or while in

recording pause mode.

= on the display flashes for 4 seconds and the tape runs

without recording. After 4 seconds, the deck enters the

recording pause mode.

2 Press 11 to reeume recording.

To insert a blank space of less than 4 seconds, press @

REC/REC MUTE again while ~ is flashing.

To insert blank spaces of more than 4 seconds, after the

deck enters recording pause mode, press

● REC/REC MUTE

again, Each time the buttonispressed, a 4-second blank space

is added.

“Can’t REC is displayed if you attempt to record on a tape with

the plastic tabs broken off.

To erase a recording

Make sure the microphone(s) is(are) not connected to this unit

and set the microphone volume and the echo level to OFF. (page

23). Also, check to make sure that BEAT and AUTO SPICE are

switched off [~aae 8).

Insert the’;a~e to be erased into deck 2 and press TAPEI

DECK 1/2 to display ‘(TP 2“.

Set the tape to the point where the erasure is to be started.

Set the reverse mode by pressing REV MODE (DECK 2).

Press

● REC/REC MUTE to starl the erasure.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Aiwa NSX-D9 Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info