Bedienungsanleitung Aiwa NSX-MT320 (Seite 14 von 76) (Englisch, Französisch, Spanisch)

496569

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

INSERTING BLANK SPACES

This section explains how to record from the tuner, CD player, or

external equipment.

—

,,___

_.-.

,11

Preparation

● Use Type I (normal) tapes only.

● Set the tape to the point where recording will start.

● Note that recording is done on only one side of the tape.

Insert the tape to be recorded on into deck 2.

Insert the tape with the side to be recorded on first facing out

from the unit.

= EJECT

Press function (CD, TUNER or VIDEO/AUX) and

prepare the source to be recorded.

To record from a CD, press CD and load the disc(s).

To record from a radio broadcast, press TUNER and tune

in to a station.

To record from a connected source, press VIDEO/AUX and

play.

Press ● REC/REC MUTE to start recording.

When the selected function is CD, playback and recording

start simultaneously.

To stop recording, press

■ ,

To pause recording, press II. (Applicable when the source is

TUNER or VIDEO/AUX) To resume recording, press it again.

To start recording with the remote control

First press

●/0 REC/REC MUTE, and then press<> within 2

seconds.

Sound adjustment during recording

The output volume and tone of the speakers or headphones may

be freely varied without affecting the recording.

Insertion of 4-second blank spaces enables you to activate the

Music Sensor function. (Applicable when the source is TUNER,

VIDEO/AUX or MD.)

1 Press ● REC/REC MUTE during recording or while in

recording pause mode.

~ on the display flashes for 4 seconds and the tape runs

without recording. After 4 seconds, the deck enters the

recording pause mode.

2 Press 11 to resume recording.

To insert a blank space of less than 4 seconds, press

●

REC/REC MUTE again while ~ is flashing.

To insert blank !Waces of more than 4 seconds, after the deck

enters recording pause mode, press

● REC/REC MUTE again.

Each time the button is pressed, a 4-second blank space is

added.

About cassette tapes

~To prevent accidental erasure, break off the plastic tabs

on the cassette tape after recording with a screwdriver or

other pointed tool.

Side A

Tab for side A

To record on the tape again, cover the tab openings with

adhesive tape, etc.

o120-minute or longer tapes are extremely thin and easily

deformed or damaged, They are not recommended.

~Take up any slack in the tape with a pencil or similar tool

before use. Slack tape may break or jam in the mechanism.

)

—

To erase a recording

● Make sure the microphone is not connected to this unit.

● Set the microphone volume to OFF (see page 19).

1 Insert the tape to be erased into deck 2 and press TAPE DECK

1/2 to display ‘(TP 2.

2 Set the tape to the point where the erasure is to be started.

3 Press

● REC/REC MUTE to start the erasure.

13 ENGLISH

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Aiwa NSX-MT320 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info