Bedienungsanleitung Aiwa NSX-V8000 (Seite 20 von 76) (Englisch, Französisch, Spanisch)

496600

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

SETTING THE TIMER

2,4

1,2

The unit can be turned on at a specified time every day

built-in timer.

Preparation

Make sure the clock is set correctly, (See page 5.)

Use the remote control.

with

the

Press the TIMER button on the remote control

once to display 0, and press the II SET button

within 4 seconds.

is displayed, and the hour flashes.

If you do not press the 11SET button within 4 seconds, another

operation may start.

Designate the hour of the timer-on time by

pressing the l<< DOWN or F>l UP button, and

the II SET button. Repeat to designate the minute

of the timer-on time.

After you designate the timer-on time, TIMER and one of the

source name flashes alternately on the display for 4 seconds.

Within 4 seconds, press one of the function

buttons to select a source.

“TIMER” and the selected source name flash alternately for 4

seconds. At this time, the selected function button does not

light up.

● If this step is not completed within 4 seconds, repeat from

step 1.

● If the TUNER button is pressed, the band cannot be selected

in this step.

Within 4 seconds, select the duration for the

timer-activated period with the

l<< DOWN or ➤>1

UP button.

The duration for the timer-activated period can be set between

10 and 240 minutes in 10-minute steps.

● If this step is not completed within 4 seconds, repeat from

step 1.

Prepare the source.

To listen to a CD, load the disc to be played first on tray 1.

To listen to a tape, insert the tape into deck 1 or 2.

To listen to the radio, tune in to a station.

Press the POWER button to turn the unit off after

adjusting the volume and tone.

remains on the display after the power is turned off (timer

standby mode).

When the timer-on time is reached, the unit turns on and

begins play with the selected source.

To check the specified time and source

Press the TIMER button on the remote control. The timer-on

time and the selected source name are displayed for 4 seconds.

However, the duration for the timer-activated period will not be

displayed.

TIMER RECORDING

Timer recording is applicable for TUNER and VI DEO/AUX (with

an external timer) sources only.

Press the TIMER button twice on the remote control so that

.~ appears on the display, and press the 11SET button within

4 seconds.

Repeat the steps shown above from step 2 and

insert the tape to be recorded into deck 2 after step 5.

To cancel timer standby mode temporarily

Press the TIMER button on the remote control so that @ or Q

disappears on the display.

To restore the timer standby mode, press again to display @ or

Using the unit while the timer is set

You can use the unit normally after setting the timer.

Before turning off the

power, repeat step 5 to prepare the source,

and adjust the volume and tone.

● Timer playback and timer recording will not begin unless the

power is turned off.

● Connected equipment cannot be turned on and off by the built-

in timer of this unit.

Use an external timer.

19 ENGL/S/-/

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Aiwa NSX-V8000 Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info