Bedienungsanleitung Aiwa XRM33 (Seite 17 von 64) (Englisch, Französisch, Spanisch)

29787

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

1,2,3,4

The unit can be turned on at a specified time every day with the

built-in timer.

Preparation

Make sure the clock is set correctly. (See page 15).

Fkess TIMER once to display “0”, then press

ENTER within 6 seconds.

“’~”

is displayed and the time flashes.

1{you press ENTER after 6 seconds, another operation may

start.

Designate the tinner-on time by turning VOLUME/

MULTI JOG or press 4+ or b-, then press

ENTER.

10 change the timer-on time by 30 minutes, press and hold

down + or >.

After you designate the timer-on time, one of the source names

flashes on the display.

F%ess any of the function buttons (TAPE, TUNER,

AUX, CD) or turn VOLUME/MIJLTl JOG or press

*H or - to

select a source, then press ENTER.

The duration for the timer activated period flashes.

Select the duration for the timer-activated period f

with VOLUME/MULTl JOG or press + or Et- E,

then press ENTER.

$1%

The duration for the timer-activated period can be set between !~~”~~

5 and 240 minutes in 5-minute steps.

,,, .,,

,,!8

~,:x:ii

.,.” ,:..:

Prepare the source.

?“,,,.

“, ,?

To listen to a CD, load the disc.

,“

To listen to a tape, insert the tape into deck.

To listen to the radio, tune in to a station.

To listen to the equipment connected to VIDEO/AUX iackg

set the timer of the connected source (with an external timer)

and prepare for the play.

Press POWERK!I STANDBY/ON to turn the unit

off after adjusting the volume and tone.

When the timer-on time is reached, the unit turns on and

begins play with the selected source.

The volume level is automatically set to 20 when the power is

turned off with the volume level set to 2“1or more.

To check the specified time and source

Press TIMER, The timer-on time, the selected source name and

the duration for the timer-activated period flash alternately for 6

seconds.

cancel timer standby mode temporarily

Press TIMER repeatedly until “@”or ‘LOREC” disappears on the

display.

To restore the timer standby mode, press TIMER once or twice

to display “@”or “0

REC”.

Using the unit while the timer is set

You can use the unit normally after setting the timer.

Before turning off the power, carry out step 5 to prepare the

❑

source, and adjust the volume and tone.

. Timer playback and timer recording will not begin unless the

power is turned off.

* Connected equipment cannot be turned on and off by the built-

in timer of this unit. Use an external timer.

... ,..,..,,

.“,””.,.,”“,.”.,””.”,..,,

...”“..”““,,-.”,‘,,,!”,%.,,,J,,”b.,,,’”.’,.!,,.,...,,,,......,,....., , ...!..%%

i_IMER REiORDING

Timer recording is applicable for TUNER and AUX/VIDEO (with

an external timer) sources only.

FWSS TIMER repeatedly Until “O REG” appearsontile display,

then press ENTER within 6 seconds.

Carry out the steps of “SETTING THE TIMER from step 2 and

insert the tape to be recorded on into deck after step 5.

● If TUNER is pressed, the band cannot be selected in

step.

this

ENGLISH 16

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Aiwa XRM33 Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info