Bedienungsanleitung Aiwa HV-DH10E (Seite 52 von 58) (Englisch)

35851

Zoom out

Zoom in

Vorherige Seite

1/58

Nächste Seite

Troubleshooting

Check the following guide for the possible cause of a problem before contacting service.

Symptom

No power.

The power is on, but

the unit does not

work.

No picture.

No sound.

The playback picture

is poor.

The unit does not

start playback.

The remote control

does not work

properly.

Correction

• Plug the power cord into the wall outlet

securely.

• Insert a disc or tape. (Check that the disc or

tape indicator in the display window is lit.)

• Select the appropriate video input mode on

the TV so the picture from the unit appears

on the TV screen.

• Press the TV/VIDEO button on the remote

control repeatedly to choose VCR mode. TV

indicator light disappears in the display

window.

• Turn on the TV.

• Select the correct input mode of the audio

receiver so you can listen to the sound from

the unit.

• Connect the audio cable securely.

• Turn on the equipment connected with the

audio cable.

• Set the audio output options setting to the

correct position (page 28), then turn on the

unit again by pressing I/6.

• Clean the disc.

• Clean video heads.

• Use CH/TRACKING i+/k– for manual

tracking adjustment while tape is playing.

• Insert a disc or tape. (Check that the disc or

tape indicator in the display window is lit.)

• Insert a playable disc. (Check the disc type

and Regional code.)

• Place the disc with the playback side down.

• Place the disc on the disc tray correctly

inside the guide.

• Clean the disc.

• Cancel the Rating function or change the

rating level.

• Point the remote control at the remote

sensor of the unit.

• Operate the remote control within 7 m.

• Remove the obstacle.

• Replace the batteries with new ones.

• When using a VCR, first press the VIDEO

button. When using a DVD, first press the

DVD button.

Cause

• The AC power cord is disconnected.

• No disc is inserted.

• No tape is inserted.

• The TV is not set to receive the unit’s signal

output.

• TV/Video mode for the unit is set to TV.

• The connected TV power is turned off.

• The equipment connected with the audio

cable is not set to receive the unit’s signal

output.

• The audio cables are not connected

securely.

• The power of the equipment connected with

the audio cable is turned off.

• The audio output options setting is wrong.

• The disc is dirty.

• Tape heads are dirty.

• Tape is a rental or was recorded on another

VCR.

• No disc is inserted.

• No tape is inserted.

• An unplayable disc is inserted.

• The disc is placed upside down.

• The disc is not placed within the guide.

• The disc is dirty.

• The Rating level is set.

• The remote control is not pointed at the

remote sensor of the unit.

• The remote control is too far from the unit.

• There is an obstacle in the path of the

remote control and the unit.

• The batteries in the remote control are

exhausted.

• This remote control has same buttons

between VCR and DVD (ex. C (PLAY)).

PM/HV-DH1(EH)/Eng/52-58 4/16/03, 5:16 PM52

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Aiwa HV-DH10E Seite 52

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info