Bedienungsanleitung Akai ALED2222BK12 (Seite 13 von 20) (Englisch)

612988

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

English - 35 -

Numeric buttons (Jump): Jumps to the preferred

channel directly via numeric buttons.

OK: Displays programme options.

Text (Search): Displays “Guide Search” menu.

(Now) : Shows the current programme.

(RECORD): The TV will start to record the selected

programme. You can press again to stop the recording.

P+P- : More event info

IMPORTANT: Connect a USB disk to your TV while the

TV is switched off. You should then switch on the TV to

enable the recording feature.

Note: Switching to a different broadcast or source is not

available during a recording.

Programme Options

In EPG menu, press the OK button to enter the Event

Options menu.

Select Channel

In EPG menu, using this option, you can switch to the

selected channel.

Record / Delete Record Timer

After you have selected a programme in the EPG menu,

press the OK button. Select the Record option and

press the OK button. After this operation, a recording

will be scheduled for the selected programme.

To cancel an already set recording, highlight that

programme and press the OK button and select the

option Delete Rec. Timer. The recording will be

cancelled.

Set Timer / Delete Timer

After you have selected a programme in the EPG menu,

press the OK button. Select the Set Timer on Event

option and press the OK button. You can set a timer

for future programmes. To cancel an already set timer,

highlight that programme and press the OK button. Then

select “Delete Timer” option. The timer will be cancelled.

Note: It is not possible to record two channels at the

same time.

Software Upgrade

YourTViscapableofndingandupdatingautomatically

via the Aerial/Cable signal.

Software upgrade search via user interface

Simply navigate on your main menu. Choose Settings

and select Other Settings menu. In Other Settings

menu navigate on to the Software for Upgrade item and

press OK button to check for a new software upgrade.

3 AM search and upgrade mode

While the TV is connected to an aerial signal. If

Automatic scanning in the Upgrade Options menu

is enabled, the TV wakes up at 03:00 and searches

broadcast channels for new software upgrades. If

new software is found and downloaded successfully,

the next time the TV powers up , it will have the new

software version.

Note: If the TV fails to come on after the upgrade unplug

the TV for 2 minutes and plug in again.

Troubleshooting&Tips

Tv will not turn on

Make sure the power cord is plugged in securely to

wall outlet. The batteries in the remote control may be

exhausted. Press the Power button on the TV.

Poor picture

• Have you selected the correct TV system?

• Low signal level can cause picture distortion. Please

check antenna access.

• Check if you have entered the correct channel

frequency if you have done manual tuning.

• The picture quality may degrade when two devices

are connected to the TV at the same time. In such a

case, disconnect one of the devices.

No picture

•No Picture means that your TV is not receiving a

transmission. Have you selected the correct button on

the remote control? Try once more. Also make sure

the correct input source has been selected.

•Is the antenna connected properly?

•Is the antenna cable damaged?

•Are suitable plugs used to connect the antenna?

•If you are in doubt, consult your dealer.

No sound

•Has the TV been set to mute? To cancel mute, press

the “ ” button, or increase the volume level.

•Sound is coming from only one speaker. Is the balance

set to one extreme? See Sound Menu section.

Remote control - does not operate

•The batteries may be exhausted. Replace the

batteries.

Input sources - can not be selected

•If you cannot select an input source, it is possible that

no device is connected. if not

•Check the AV cables and connections if you have tried

to connect a device.

Recording unavailable

Torecordaprogramme,youshouldrstconnectaUSB

disk to your TV while the TV is switched off. You should

then switch on the TV to enable recording feature. If

you cannot record, try switching off the TV and then

re-inserting the USB device.

USB is too slow

If a “USB is too slow” message is displayed on the

screen while starting a recording, try restarting the

recording. If you still get the same error, it is possible that

your USB disk does not meet the speed requirements.

Try connecting another USB disk.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Akai ALED2222BK12 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Akai ALED2222BK12

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info