630567
24
Zoom out
Zoom in
Vorherige Seite
1/52
Nächste Seite
22
Adjusting the Reverb Effect Volume of Each Program
This procedure adjusts the volume of the Reverb effect for each Program individually, as opposed to the
overall Reverb effect volume. The Reverb effect volume of each program is stored in the EWI4000s.
1. Select the program whose Reverb effect volume you want to adjust.
2. While holding the FX BUTTON, press the SETUP BUTTON. While pressing
both these buttons, “rb” will be shown in the PROGRAM / DATA DISPLAY.
3. Release both buttons. The current Reverb effect volume of the selected
program will be displayed.
4. Adjust the Reverb effect volume by pressing the HOLD BUTTON (which increases the volume value) or
OCTAVE BUTTON (which decreases the volume value).
5. Press the SETUP BUTTON. The EWI4000s will return to Play Mode.
Adjusting the Delay Effect Volume of Each Program
This procedure adjusts the Delay effect volume for each Program. The Delay effect volume setting of each
program is stored in the EWI4000s.
1. Select the program you wish to adjust the Delay effect volume.
2. While holding the FX BUTTON, press the SETUP BUTTON. While pressing both these buttons, “rb
will be shown in the PROGRAM / DATA DISPLAY.
3. While pressing the SETUP BUTTON, release the FX BUTTON, then press the
HOLD BUTTON so the PROGRAM / DATA DISPLAY now shows “dL.”
4. Release the SETUP BUTTON and HOLD BUTTON. The current Delay volume
of the selected Program will be displayed.
5. Adjust the Delay volume by pressing the HOLD BUTTON (which increases the volume value) or
OCTAVE BUTTON (which decreases the volume value).
6. Press the SETUP BUTTON. The EWI4000s will return to Play Mode.
Adjusting the Chorus Effect On/Off on Each Program
This procedure selects whether the Chorus effect is set on or off for each Program. The Chorus effect
setting of each Program is stored in the EWI4000s.
1. While holding the FX BUTTON, press the SETUP BUTTON. While pressing both these buttons, “rb
will be shown in the PROGRAM / DATA DISPLAY.
2. While pressing the SETUP BUTTON, release the FX BUTTON, then press the
HOLD BUTTON so the PROGRAM / DATA DISPLAY now shows “CH.”
3. Release the SETUP BUTTON and HOLD BUTTON. The current Chorus setting
of the selected program will be displayed.
4. Set the Chorus to eitheron” or “OF” by pressing the HOLD BUTTON or OCTAVE BUTTON.
5. Press the SETUP BUTTON. The EWI4000s will return to Play Mode.
24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Akai EWI4000s wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info