Bedienungsanleitung Akai EWI4000s (Seite 31 von 52) (Englisch)

630567

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

CHAPTER 4: USING THE EWI4000s AS A MIDI CONTROLLER

Because the EWI4000s has internal sounds and effects, you can play it on its own, but you can also it as

MIDI controller for an external MIDI sound module/synth.

ABOUT MIDI

MIDI is a standard for transferring the performance data between electronic instruments regardless of the

manufacturer. Devices are connected using a 5-pin MIDI cable. When you connect the EWI4000s’ MIDI

OUT to the MIDI IN of a MIDI sound module, the EWI4000s’s performance data will be sent to the module,

which plays the sound. MIDI data is not actual sound – just data which tells the module what sound to

produce and how to manipulate it.

MIDI data can be sent over 16 MIDI channels in one MIDI cable. If you are using an external module, you

must set the same MIDI channels for the both the EWI4000s and the sound module (whether or not you are

using the EWI4000s’s sounds or effects). For example, if the EWI4000s’s output channel is set to “1,” the

sound module’s input channel should also be “1.”

When sending MIDI data, the EWI4000s transmits the Note Number, Velocity, and some Controller Changes

such as Breath Controller, Portamento, Sustain, etc.

1. Connect the MIDI OUT of the EWI4000s to the MIDI IN of your external MIDI sound module using a

standard 5-pin MIDI cable.

2. Set the external sound model so that it responds to the incoming MIDI signal.

3. Set the received MIDI channel to “1.” (The EWI4000s is set so that it transfers the MIDI signal with its

initial setting.)

4. Select the sound library you wish to play.

Note: Refer to your external MIDI sound module’s manual for more information.

Transmitted Information from the EWI4000s MIDI OUT:

y Breath strength is transmitted as MIDI Control Change (CC) #2 (Breath Controller). If the

external sound module accepts this information, you can control the output volume of the sound

module with your breath. Depending on the sound module, your breath strength can change not

only the output volume but also the character of the sound. For example, if you set the cut-off

frequency of the sound module with MIDI CC #2, your breath strength can change the sound

character by changing the cut-off frequency of the sound. Refer to your sound module’s manual

for more information.

y BEND PLATE information is transmitted as MIDI Pitch Bend data. If the external sound module

accepts this information (i.e., if Pitch Bend is a registered parameter), you can control the sound

module’s Pitch Bend with the BEND PLATE of the EWI4000s. (The vibrato information is also

transmitted as MIDI Pitch Bend data.).

y GLIDE PLATE information is transmitted as MIDI Control Change #65 (Portamento) and #5

(Portamento Time). If the external sound module accepts them, you can control the sound

module’s Portamento with the GLIDE PLATE of the EWI4000s.

 MIDI Program Change

You can change the sound program of an external sound module by sending MIDI Program Change

information from the EWI4000s. The operation for a Program Change is the same as “Selecting the Internal

Sounds (Program Key).” When the Program of the EWI4000s is changed, the MIDI Program Change of the

same number is transmitted.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Akai EWI4000s Seite 31

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info