Bedienungsanleitung Akai MINIAK (Seite 11 von 60) (Englisch)

630576

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

EDITING SEQUENCES

Choose an existing Sequence to edit by pressing the [SEQUENCES]

button and turning the DATA DIAL. Hold down any key to play the

Sequence. (Use the [TAP TEMPO] button to change the tempo.)

Once you've found a Sequence you want to edit, press the DATA

DIAL to enter edit mode. Turn the DATA DIAL to cycle through the

different options. Press the DATA DIAL to toggle in and out of editing

the current parameter.

Here are the Sequence editing options:

1. Revert-to-stored? / Unrevert-to-edited?

If you have edited a Sequence, you may revert back to the original version. Press the DATA DIAL to revert.

Go back to your edited state by press the DATA DIAL a second time to unrevert.

You can revert and unrevert to compare your changes with the original Sequence. When you're satisfied

with your work, press [STORE] to save your changes.

2. Send to Multi?

Pressing the DATA DIAL at this option sends you to Multi Mode and

allows you to make this Sequence a part of the last-selected Multi.

If the Multi does not have any parts, this Sequence is automatically

assigned to the Multi's part A.

If the Multi already has one or more parts, you will be able to add the

Sequence in one of the following ways:

1. send to part. The Multi's part will use this Sequence. Remember

that a part uses both a Program and a Sequence. If the part's

Program is set to "(Sequence's pgm)", then the Sequence will sound

just as it does in Sequences mode. Otherwise, the Multi will play the

Sequence using the part's own Program.

2. layer. The Multi's existing part is duplicated, resulting in a new part.

The Sequence is then sent to the new part.

3. split low. The Multi's existing part is split in two at a particular key.

The MINIAK prompts for a note on the keyboard at which to execute

the split. The Sequence is then sent to the lower part of the split.

Every note below the one you select will use this new Sequence.

Every note including and higher than the note you select will use the

Multi's existing part.

The new part is assigned the next letter after the split part. For

example, if the Multi contains parts A, B, C, and D, and part B is the

part that gets split, then part C will be the newly-added part. All later parts' letters are incremented by one.

To select the split point, turn the DATA DIAL or play a key. You can use the [OCTAVE] buttons if your

desired split point is outside of the current key range.

4. split high. The Multi's existing part is split in two at a particular key. As with the split low option, the

MINIAK prompts for a note on the keyboard at which to execute the split. The Sequence is then sent to the

upper part of the split. Every note above the one you select will use this new Sequence. Every note

including and lower than the note you select will use the Multi's existing part.

To select the split point, turn the DATA DIAL or play a key. You can use the [OCTAVE] buttons if your

desired split point is outside of the current key range.

5. add part. The Sequence is added as a brand new part. All other part parameters are set to their default

values.

Store your Sequenc

The [STORE] button will light

once you have edited a

Sequence.

Press [STORE] after you're

satisfied with your edits.

Otherwise, your changes will be

lost when you turn off your

MINIAK.

Send to Multi only allows the

option of sending the Sequence

to the current Multi. Therefore,

you may need to jump out of

Sequence editing to choose a

Multi before returning to

Sequence and following this

procedure.

How part letters change when

"layer," "split low," and "split

high" are used: When parts are

layered or split high, the new

part is assigned the next letter

after the targeted part. All

subsequent part letters are

incremented by one.

For example, consider a Multi

with four existent parts: A, B, C,

If we split part B, the result is as

follows: A, B (low split of B), C

(high split of B), D (formerly "C"),

E (formerly "D").

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Akai MINIAK Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Akai MINIAK

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info