Bedienungsanleitung Akai MPC2500 (Seite 36 von 136) (Englisch)

630577

Zoom out

Zoom in

Vorherige Seite

1/136

Nächste Seite

MPC2500 Operator’s Manual rev 1.0

Chapter 4: Editing sequences

Chapter 4 : Editing sequences

There are two ways to edit sequences. You can select a region and edit all events at one time, or you can edit each event in

detail. In this section, you will learn about the SEQ EDIT mode, where you can select a region to edit your event(s).

Selecting a region within a

track to edit

You can edit the events within a region that you set in the

track. This is done in the EVENTS page of the SEQ EDIT

mode, which can be accessed by pressing the [MODE] key

and then the [PAD 13].

Selecting a region for the editing

In the EVENTS page, there are 3 different editing op-

tions in the Edit field: COPY, MOVE and TRANSPOSE.

The procedure to select the editing region is the same

for all three options. Let us begin with the selection of

the editing region.

• Setting the time

Select the Time field in the EVENTS page of the

SEQ EDIT mode.

In the Time field, you can set the start and end

points of the editing region. For example, to edit

the first bar of a 2-bar sequence, set this field to “

001.01.00 - 002.01.00 ”. In this case, the event at the

“002.01.00” point will not be edited.

If you set the end point “002.01.00”, like in this

picture, the area right before this point will be in-

cluded in the area.

002.01.00

001.04.95001.04.94 002.01.01001.04.93

EVENT EVENT EVENT EVENT EVENT

• Setting the pad/note number

01. Select the Notes field in the EVENTS page of the

SEQ EDIT mode.

The display of the Notes field depends on the type

of the track that you have selected.

• When DRUM track is selected:

In default, the field is set to ALL, which means the

MPC2500 will edit all the pads. If you wish to edit

only a specific pad, position the cursor in the Notes

field and hit the desired pad. The pad number will

be displayed in the Notes field. You can select sev-

eral pads. If you hit a different pad by mistake, you

can cancel the selection by hitting the pad again.

To restart the pad selection, turn the DATA wheel

to the left. The value in the Note field will be reset

to ALL so that you can select the pad that you want

from the beginning.

When MIDI track is selected:

The display changes to show the selected region

by note number.

You will set the upper limit and the lower limit of

the note in the field, The MPC2500 will edit only

the events within the note numbers set in this field.

Copying events (COPY)

You can copy events within the selected region to another

place. The source data will remain in the original location.

01. Select the Edit field in the EVENT page of the SEQ

EDIT mode, and select COPY.

The various fields necessary for the copying will

be displayed.

02. In the Time field and the Notes field, select the region

and notes that you wish to copy.

03. In the From sq field and the Tr field in the right, select

the source sequence and track.

04. In the To sq and the Tr field in the right, select the

destination sequence and track.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Akai MPC2500 Seite 36

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Akai MPC2500

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info