Bedienungsanleitung Akai MPC2500 (Seite 105 von 136) (Englisch)

630577

105

Zoom out

Zoom in

Vorherige Seite

1/136

Nächste Seite

MPC2500 Operator’s Manual rev 1.0

Applying filters to an

incoming signal

You can apply the internal filters to the incoming signal from

REC IN (Analog) or DIGITAL IN (Digital). You can also

control the cut-off frequency and Resonance in real-time by

using Q-Link slider/knob.

01. Press [INPUT THRU] key.

The INPUT page will be displayed.

You can also get to the INPUT page by pressing the

[F5] (INPUT) key in the MIXER mode.

Set the necessary parameter in each field while refer-

ring to the Applying effects to an incoming signal.

02. In the Type field, select the filter type.

Setting set the filter type is same as in the Filter page

while in PROGRAM mode. Refer to “Editing the

sound of a sample” in the PROGRAM mode.

Note : You cannot use the Filter Modulation with INPUT THRU.

Using Q-Link feature in

INPUT THRU mode

You can control the input level, pan, and the filter’s param-

eter ( Cut-off frequency and Resonance) in real-time by us-

ing Q-Link slider/ knob.

Note : You cannot record the real-time control of the INPUT

THRU into the sequence.

Note : In this explanation, the necessary setting on the filter and

the input level/pan for INPUT THRU mode should be entered

first. If you haven’t set any parameter for them, set them while

referring to “Applying effects to an incoming signal” and “Ap-

plying filters to an incoming signal”

01. Select SLIDER mode by pressing [MODE] key then

hitting PAD 1 (SLIDER)

02. In the Assign pad field, select IN.

Note : Only “REALTIME” will be available in the Change field.

03. In the Parameter field, adjust the desired parameter.

LEVEL : This control the input signal volume level.

CUTOFF1+2 :

This controls the cutoff frequency of both Fil-

ter 1 and Filter 2.

CUTOFF1 : This controls the cutoff frequency of Filter 1.

CUTOFF2 : This controls the cutoff frequency of Filter 2.

RESO1+2 : This controls the resonance value of both Fil-

ter 1 and Filter 2.

RESO1 : This controls the resonance value of Filter 1.

RESO2 : This controls the resonance value of Filter 2.

PAN : This control the sample’s pan position.

04. In the High range field and Low range field, set the

upper and lower limit of the slider or knobs.

The value of the controlled parameter is deter-

mined by the value set here. The value depends

on the type of the parameter selected in the Pa-

rameter field.

LEVEL : 0 –100.

This is linked to the value in Level field in the INPUT

page. If you change the slider or knob, the value will

be changed depending on the value in INPUT page.

CUTOFF1+2 / CUTOFF1 / CUTOFF 2

: -50 - +50

This value also offsets the current setting in the

INPUT page.

RESO1+2 / RESO1 / RESO2 : -50 - +50

Again, this value offsets the current setting in the

INPUT page.

Note : In the Input THRU mode, you cannot record the moving

of Q-Link in the sequence.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Akai MPC2500 Seite 105

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Akai MPC2500

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info