Bedienungsanleitung Akai MPD26 (Seite 15 von 32) (Englisch)

630216

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

MIDI PORT/CHANNEL FIELD

CONTROL CHANGE FIELD

MINIMUM RANGE FIELD

MAXIMUM RANGE FIELD

CONTROL CHANGE PARAMETERS

The following list of parameters can be accessed if the event type for the knob or fader is set to Control

Change.

MIDI CHANNEL FIELD

This field sets the MIDI Port and Channel which the knob or fader will use to

transmit messages. You can assign knobs and faders to one of two MIDI Ports,

A or B, and to one of 16 MIDI Channels on each port (i.e. A14). You can also

assign a knob or fader to use the MIDI Common Channel.

1. Press [<] to select MIDI Port/Channel field.

2. While in MIDI Port/Channel field, use [VALUE] dial to select desired MIDI

Port and Channel.

3. Press [>] to select the next field.

Note: When not used via USB, only knobs and faders assigned to port A

will be transmitted via the 5-pin MIDI port on the back of the MPD26.

CONTROL CHANGE FIELD

In this field you can set which MIDI CC # the knob or fader will transmit when it

is used.

1. Use [<] or [>] to select Control Change field.

2. While in Control Change field, use [VALUE] dial to select desired Control

Change Number.

3. Press [>] button to select the next field.

Note: To control a parameter in your DAW or sound module with a knob or

fader, both the parameter and the physical controller should be set to the same

Controller Number.

MINIMUM RANGE FIELD

This field is used to specify the minimum value that the knob or fader can

output.

1. Use [<] or [>] to select Minimum Range field.

2. While in Minimum Range field, use [VALUE] dial to select desired minimum

value.

3. Press [>] button to select the next field.

Tip: Sometimes you might not want the full 0-127 range of control that a fader

automatically defaults to. Often, reducing the value range of the fader might

give you more precise control over the parameter it is controlling. For example,

if you are using one of the faders to control a synced delay line, there might only

be about 10 available values for the sync delay time (1/2, 1/4, 1/8 note, etc.).

Therefore, it wouldn’t make much sense to have the fader transmit the full 128

MIDI control values, since this only gives you a tenth of the full fader range.

Instead, try setting the maximum value of that fader to 10.

MAXIMUM RANGE FIELD

This field is used to specify the maximum value that the knob or fader can

output.

1. Use the [<] or [>] buttons to select Maximum Range field.

2. While in Maximum Range field, use [VALUE] dial to select desired maximum

value.

Tip: Setting the maximum value of a controller lower than the minimum value

will cause the knob or fader to behave inversely. For example, if you are

controlling an interface or plug-in that operates with a drawbar structure, such

as organ instruments, it might be more intuitive to invert your faders.

When finished editing, press [ENTER] to save or [<] to cancel the changes.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Akai MPD26 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info