Bedienungsanleitung Akai MPD32 (Seite 38 von 42) (Englisch)

630559

Zoom out

Zoom in

Vorherige Seite

1/42

Nächste Seite

TROUBLESHOOTING

PROBLEM CAUSE SOLUTION

Please make sure that the MPD32 is connected to your

computer and that the computer is powered on.

The display does not light up. No power.

If using a power adapter, please make sure that the

adapter is plugged into a live power outlet.

Check your computer’s USB connection to confirm that

the MPD32 is recognized. If necessary, replug the

connection and restart your computer.

MPD32 not properly

connected.

If controlling an external hardware module, make sure

that the MPD32’s MIDI OUT is connected to the device’s

MIDI IN port.

MPD32 connected after

software application has

started.

Restart the software application with the controller

plugged in.

Problem is caused by use of

a USB hub.

Unplug the MPD32 from the USB hub and connect

directly to your computer.

Software application not set

to receive MIDI data from the

MPD32.

Ensure that the MPD32 or “USB” MIDI device is listed as

an active MIDI source in your application. Usually, the

MIDI settings can be accessed through the application’s

Preferences menu.

No sound from target device.

MPD32’s MIDI channel not

the same as application’s

incoming MIDI channel.

Make sure that the MPD32 is sending MIDI information

on the channel that the target device expects.

Footswitch was plugged in

after the MPD32 was

powered on.

Turn the unit’s power off, wait a moment and then turn it

on again.

Notes sustain continuously.

Stuck notes due to

incomplete MIDI data.

Turn the unit’s power off, wait a moment and then turn it

on again.

Footswitch works in reverse.

Footswitch was plugged in

after power was turned on.

With the footswitch plugged in, turn the unit’s power off,

wait a moment, and turn it on again.

Note Repeat is not

synchronized to my clock

source.

Clock source on MPD32 set

to “Internal”.

In Global Mode, change the MIDI Clock setting to

“External”. Also, make sure that your software is set to

send MIDI Clock to the MPD32.

My Seq/DAW is set to send

clock but Note Repeat is not

working.

Software DAW is not in play

mode.

If your software DAW is not playing, it will not be sending

clock.

My fader or knob works in

reverse.

Controller minimum value is

set higher than its maximum.

Edit the controller and set the minimum value to be lower

than the maximum.

Transport control does not

work.

Software does not support

MMC messages, MIDI

START/STOP or the MIDI

CC mode.

Edit the transport control to send MIDI messages

instead. Make sure that the Transport mode on the

MPD32 matches the receive mode of your software.

I am only hearing one sound

when I hit different pads

16 Level function is engaged.

When engaged, the 16 Level function will map the last

hit pad to all 16 pads. Deactivate 16 Level to return to

normal operation.

The pads always play at

maximum velocity (127).

Full Level feature is engaged.

When engaged, the Full Level function will cause all the

pads to output maximum velocity, no matter how hard

they are hit. Turn off Full Level to return to normal

operation.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Akai MPD32 Seite 38

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Akai MPD32

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info