Bedienungsanleitung Akai MPK88 (Seite 6 von 72) (Deutsch, Englisch, Französisch, Italienisch, Spanisch)

630552

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

103

111

119

127

87 95

14. 16 MPC PRESSURE AND VELOCITY SENSITIVE

PADS – The pads can be used to trigger drum hits or

samples on your software or hardware module. The

pads are pressure and velocity sensitive, which

makes them very responsive and intuitive to play.

15. PAD BANK buttons – These 4 buttons

switch among pad banks A, B, C, D.

Each bank can address a unique set of 16

sounds, giving you access of up to 64 different

sounds you can trigger with the pads. The currently

selected pad bank will be indicated on the LCD

display

16. [FULL LEVEL] – When [FULL LEVEL] is activated,

the pads always play back at a maximum velocity

(127), no matter how hard or soft you hit them.

17. [16 LEVEL] –When [16

LEVEL] is activated, you can

use the pads to change a

selected sound’s velocity in

16 steps. When you press

the button, the last pad that

was hit gets mapped to all

pads. The pads will now

output the same note

number and pressure controller as the initial pad, but

the velocity is fixed at the values shown in the

diagram on the right, regardless of how hard you hit

them. This allows you to have more control over the

velocity of a sound.

18. [NOTE REPEAT] – Holding this button while striking

a pad causes the pad to retrigger at a rate based on

the current Tempo and Time Division settings. The

Note Repeat feature can be synced to an internal or

external MIDI Clock source. [NOTE REPEAT] can

function as a latching or momentary button.

19. [SPLIT] – This button divides the keyboard into left

and right sections – A and B, respectively – allowing

you to control two different sets of sounds

simultaneously. When [SPLIT] is activated, its LED

will light up.

20. [TIME DIVISION] – This button is used to specify the

rate of the Note Repeat and Arpeggiator features.

When [TIME DIVISION] is activated, you can press

one of the 8 switches to specify a time division.

[TIME DIVISION] can function as a momentary or

toggle button.

Please note that while [TIME DIVISION] is active, the

8 assignable buttons will not function as MIDI CC or

Program Change switches until [TIME DIVISION] has

been de-activated.

21. [ARP ON/OFF] – This button enables and disables

the internal Arpeggiator. The Arpeggiator will only

function on notes being played on the keyboard. The

Arpeggiator feature on the MPK61/MPK88 works in

conjunction with the Tempo and Time Division

settings, which specify the rate of arpeggiation.

Please note that the Arpeggiator can be synced

either to an internal or external MIDI Clock source

(such as a software DAW or a MIDI device).

22. [LATCH] – This button works in conjunction with the

Arpeggiator. When the Arpeggiator is turned on and

[LATCH] has been enabled, you can hold down a

combination of keys -- the Arpeggiator will memorize

and continue to arpeggiate these notes, even if you

depress the keys. There are a couple of ways to use

the [LATCH] function:

a. While holding down the keys, you can add

more notes to the sequence by pressing down

additional keys.

b. If you depress the keys, release them, and

then press down a new combination of notes,

the Arpeggiator will memorize and arpeggiate

the new notes.

23. [OCTAVE + / -] – These buttons can be used to shift

the keyboard’s range up and down. The display will

indicate which octave you have shifted to. If both

buttons are pressed at the same time, the octave

shift will reset to 0.

24. [TAP TEMPO] – This button allows you to tap in a

new tempo. If the preset is reloaded, the tempo will

revert to the saved tempo value. (Please note that a

preset’s default tempo can be set in Edit Mode). Tap

Tempo does not work when the MPK61/MPK88 is set

to External sync.

25. PITCH BEND WHEEL – Transmits MIDI Pitch Bend

information on a selected MIDI channel and port.

26. MODULATION WHEEL – This wheel can be used to

transmit continuous controller data. By default, the

modulation wheel will transmit MIDI CC #01.

Tip: You can set the dividing point of the

keyboard – or "Split Point" – by simply holding

down the [SPLIT] button and pressing the desired

key on the keyboard.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Akai MPK88 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Akai MPK88

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info