Bedienungsanleitung Akai MPK88 (Seite 19 von 44) (Englisch)

630552

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

MIDI PORT/CHANNEL FIELD

CONTROL CHANGE FIELD

MINIMUM RANGE FIELD

MAXIMUM RANGE FIELD

CONTROL CHANGE PARAMETERS

The following list of parameters can be accessed if the pad event type is set to “Note”.

MIDI CHANNEL FIELD

This field sets the MIDI Port and Channel which the knob or fader will use to

transmit messages. You can assign knobs and faders to one of two MIDI Ports,

A or B, and to one of 16 MIDI Channels on each port (i.e. A14). You can also

assign a knob or fader to use the MIDI Common Channel.

1. Use the [<] button to select MIDI Port/Channel field.

2. While in MIDI Port/Channel field, use [VALUE] dial to select desired MIDI

Port and Channel.

3. Use the [>] button to select the next field.

Note: When not used via USB, only knobs and faders assigned to port A will be

transmitted via the 5-pin MIDI port on the back of the MPK61/MPK88.

CONTROL CHANGE FIELD

In this field you can set which Control Change Number the pad will transmit

when it is pressed.

1. Use [<] or [>] buttons to select Control Change field.

2. While in Control Change field, use [VALUE] dial to select desired Control

Change Number.

3. Use the [>] button to select the next field.

Note: To be able to control a parameter in your DAW or sound module with a

knob or fader, both the parameter and the knob need to be set to the same

Controller Number.

MINIMUM RANGE FIELD

This field is used to specify the minimum value that the knob or fader can

output.

1. Use [<] or [>] buttons to select Minimum Range field.

2. While in Minimum Range field, use [VALUE] dial to select desired minimum

value.

3. Use the [>] button to select the next field.

Tip: Sometimes you might not want the full 0-127 range of control that a fader

automatically defaults to. Often, reducing the value range of the fader might

actually give you more precise control over the parameter it is controlling. For

example, if you are using one of the faders to control a synced delay line, there

might only be about 10 available values for the sync delay time (1/2, 1/4, 1/8

note, etc.). Therefore, it wouldn’t make much sense to have the fader transmit

the full 128 MIDI control values, since that only gives you a tenth of the full fader

range. Instead, try setting the maximum value of the fader to 10.

MAXIMUM RANGE FIELD

This field is used to specify the maximum value that the knob or fader can

output.

1. Use the [<] or [>] buttons to select Maximum Range field.

2. While in Maximum Range field, use [VALUE] dial to select desired maximum

value.

Tip: Setting the maximum value of a controller lower than the minimum value

will cause the knob or fader to behave inversely. For example, it may be more

intuitive to invert your faders if you are controlling an interface or plug-in that

operates with a drawbar structure, such as organ instruments.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Akai MPK88 Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Akai MPK88

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info