Bedienungsanleitung Akai Timbre Wolf (Seite 12 von 64) (Deutsch, Englisch, Französisch, Italienisch, Spanisch)

630521

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

Sequencer

You can edit the sequences (and fills) of each pattern using Timbre Wolf’s Step Switches and/or

keyboard.

Note: While Timbre Wolf’s sequencer plays, it will send out its MIDI note messages for all four tracks

(each on its corresponding channel) through its USB port and MIDI Out, regardless of the voice

mode or any performance on Timbre Wolf’s keyboard. You can use this feature to sequence external

devices (drum machines, other synths, etc.) along with Timbre Wolf.

Step Switches

You can use the 16 Step Switches to enter or remove notes from the sequence simply by pressing

the corresponding Step Switches.

To enter or remove steps, press the Mute/Select button for the voice whose steps you want to

enter or remove, and then press one or more Step Switches to enter or remove notes at those

positions. The notes are entered with the default Step Switch velocity (described below).

For each voice, each step has a note value, which you can set in two different ways:

• To set the note value of one or more specific steps, press and hold the desired Step

Switches and turn the Tempo knob. If you are adjusting only one note, the note value will be

shown in the display. If you are adjusting multiple notes, the display will show how many

semitones up or down you are shifting them. Each voice has a three-octave range.

• To set the default note value, press a key on Timbre Wolf’s keyboard. This will be the note

value that is recorded when you select a step. This is useful for setting the note value before

entering your steps.

For each voice, each step has a velocity, which determines how loud the note is played. You can set

this in two different ways:

• To edit a single step’s velocity, press and hold the Velocity button and then press the

desired Step Switch to cycle between the available velocities: low (green), medium (amber),

high (red), and off (unlit).

• To select the default Step Switch velocity, press the Velocity button to cycle through the

available default velocities: low (green), medium (amber), and high (red). This will be the

velocity that is recorded when you select a step or press the pad. This is useful for setting the

velocity before entering your steps.

Keyboard

You can use Timbre Wolf’s keyboard to record a sequence in real time. The notes you play will be

quantized (aligned) automatically with the steps. Your recording will be “overdubbed” onto the

sequence(s), but recording a note over an already existing note will replace it.

To record while stopped, press Rec to record-arm the sequencer, and then press Play/Stop to

start recording, or press Rec to cancel recording.

To record during playback, press Rec. Recording will begin immediately. Press Rec again to stop

recording while playback continues, or press Play/Stop to stop both recording and playback.

Before or while you are recording, press the Mute/Select button for the voice you want to use to

record.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Akai Timbre Wolf Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info