Bedienungsanleitung Al-ko 546 127130 (Seite 35 von 76) (Deutsch, Englisch, Französisch, Spanisch)

592598

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

Maintenance and care

Checking Oil level:

Observe the notes and instructions in the type-

speci.c engine operating instructions.

• Place lawn mower

horizontally with all

wheels on the ground.

• Turn oil tank cap

counter-clock-wise

(14), and remove.

Wipe off dipstick.

• Place dipstick back

into filler pipe.

• Remove dipstick, hold horizontally and read oil

level. Oil level has to be between the

"MAXIMUM" and "MINIMUM" markings.

Changing the motor oil:

• Have a suitable container ready to collect the

used oil.

• Drain or suction off all the oil through the oil

filler opening.

Attention:

Dispose of used motor oil in a manner that is

compatible with the environment!

Used oil should not be

• Dispoed of with domestic rubbish

• Poured into the sewage system or drains

• Poured out onto the ground

Gearbox *

The gear is equipped with a special permanent oil

and operates completely maintenance-free.

Technical faults that cannot be resolved by

adjusting the Bowden throttle cable are only to be

corrected by an authorized Service Center.

* depending on version

8.5 Height adjustment

Before storing your lawnmower out of season

clean and lubricate the wheel adjuster spindle with

grease (this procedure is necessary at least

annually).

For this, set the wheel adjuster to its highest

position (max)

- clean and lubricate the exposed part of the

spindle with grease

- then set the wheel adjuster to its lowest position

(min)

- clean and lubricate the remaining spindle with

grease.

8.6 Mowing Blade

Special tools, such as a torque wrench for

example, are required to mount the blade to

the mower. For safety reasons we recommend that

the mowing blade is sharpened, balanced and re-

fitted by an authorized specialist workshop only.

The following notes are therefore only intended for

specialist repair shops.

To obtain best mowing results we recommend to

have the blade sharpened / balanced or at least

once every year.

Replacement of Blade

Proper gloves are to be worn when

replacing the blade. The spark plug

cap has to be removed prior to any

work.

When replacing any blade parts only SOLO spare

parts are to be used. The identification No. on the

blade has to agree with the Order No. for the

replacement. Never install a different type of blade!

Use the holding pin as a blocking device for the

blade. The blade fastening screw has a regular

right-handed thread. To remove the screw we

recommend using a socket wrench 21 mm (spark

plug wrench) or hex. wrench 8 mm, 5/16“. At re-

assembly of the overload clutch be sure and

observe the sequence in which these parts where

previously assembled. The blade screw is to be

tightened with the specified torque of 45Nm

(4,5mkp).

Fig. 12

Fig. 11

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Al-ko 546 127130 Seite 35

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info