Bedienungsanleitung Al-ko 582 127129 (Seite 30 von 68) (Deutsch, Englisch, Französisch, Spanisch)

603973

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

8 Maintenance and care

For your own safety, remove the spark

plug cap from the spark plug (12) prior

to any maintenance work or cleaning.

Any maintenance and care that go beyond the

described explanations need to be left to an

authorized Service Center.

8.1 Cleaning the mower

After each use, the mower needs to be

thoroughly cleaned. Special attention needs to

be given to the lower side, the blade and the

cutting area circle.

Tip: To enable the lawnmower to be maintained

and cleaned with an empty fuel tank, fill only

enough fuel for the mowing job in hand. That

way, the tank can be quickly emptied after

mowing has been completed.

After releasing handle screw (15), the mower

can be raised onto its rear wheels and be

supported on the lower handle. First pull the

spark plug cap. The fuel tank should be empty,

if possible, to prevent fuel spilling from the fuel

tank cap. Catch any fuel running out of the

carburettor with a suitable rag.

Dirt and grass debris is removed easily

immediately after mowing. Imbedded grass

debris and dirt on the mower deck‘s lower

section interrupt the grass collection and affect

cutting results. Imbedded dirt on the blade and

on the blower wheel lead to imbalance and

consequently to vibration.

Check also for cleanliness of the duct.

The ejection air duct can be cleaned with a

small stick or with a screw driver.

Do not spray the mower with a hose or high

pressure cleaning hose.

The engine has to remain dry.

The outer deck parts can simply be kept clean

by wiping the unit off with a rag. Strong cleaning

agents of any kind are not to be used.

8.2 Wheel axles and wheel hubs

Wheel axles and wheel hubs are to be

lubricated occasionally (at least once a year).

Remove the wheel cap, loosen the screw and

remove the wheel. During disassembly observe

the sequence for the reassembly of the parts.

8.3 Height adjustment

Before storing your lawn mower out of season

clean and lubricate the wheel adjuster spindle

with grease (this procedure is necessary at

least annually).

For this, set the wheel adjuster to its highest

position (max), clean and lubricate the exposed

part of the spindle with grease. Then set the

wheel adjuster to its lowest position (min), clean

and lubricate the remaining spindle with grease.

8.4 Air filter maintenance

Follow the instructions of the manufacturer of

the motor.

8.5 Mowing blade

To obtain best mowing results we recommend

to have the blade sharpened / balanced or

replaced at least once every year.

Special tools, such as a torque wrench for

example, are required to mount the blade

to the mower. For safety reasons we

recommend that the mowing blade is

sharpened, balanced and re-fitted by an

authorized specialist workshop only. The

following notes are therefore only intended for

specialist repair shops.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Al-ko 582 127129 Seite 30

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info