Bedienungsanleitung Al-ko 7500 (Seite 11 von 120) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Finnisch)

601620

Zoom out

Zoom in

Vorherige Seite

1/120

Nächste Seite

Scope of supply

467 769_a 11

corrosive, flammable, explosive or fuming

fluids

fluids that are hotter than 35 °C

water containing sand and abrasive fluids.

➯

only on Drain pump

SCOPE OF SUPPLY

Thermal protection

The equipment is fitted with a thermal protection

switch which switches the motor off in the event

of overheating. After a cooling-down phase of ap-

prox. 15 - 20 minutes the pump switches on auto-

matically.

Operate the unit only if the immersion pump is fully

immersed.

SAFETY INSTRUCTIONS

CAUTION!

Danger of injury!

Only use the machine and the extension

cable if it is in perfect technical condition!

Damaged units must not be used.

Safety and protective devices must not

be deactivated!

Children, or people who are not familiar with

the operating instructions, are not allowed to

use the machine.

Never lift, transport or suspend the unit using

the connection cable.

Unilateral modifications or conversions of the

unit are prohibited.

Electrical safety

CAUTION!

Danger when touching voltage con-

ducting parts!

Disconnect the plug from the mains if the

extension cable is damaged or severed!

We recommend connecting a RCD (re-

sidual current operated device) having a

nominal residual current of < 30 mA.

The house mains voltage must agree with the

details quoted in the technical data, do not

use any other supply voltage.

The unit must only be operated with an

electrical installation in accordance with DIN/

VDE 0100, Part 737, 738 and 702 (swimming

pools). Protection must be provided by a 10 A

line protection switch and a RCCD (residual

current operated device) having a nominal re-

sidual current of 10/30 mA.

Use only extension cables that are suitable

for use outdoors - minimum cross-section 1.5

. Cable drums should always be unrolled

completely.

Damaged or brittle extension cables must not

be used.

➯

Check the condition of your extension

cable each time you start to use the

equipment.

ASSEMBLY

Mounting the pressure line

see Fig. A

1. Screw the connection elbow (7) into the pump

outlet.

2. Screw the combination nipple (5) into the con-

nection elbow.

3. Fix a hose to the combination nipple.

ADVICE

The combination nipple can be trim-

med to suit the selected hose con-

nection. Use the largest possible

hose diameter.

STARTUP

Safety

CAUTION!

Exclude, by suitable means, that, in the

event of a fault in the immersion pump,

consequential damage is caused by floo-

ding.

Make sure that the immersion pump is stan-

ding securely or operate the immersion pump

suspended from a rope.

Make sure there is adequate clearance under

the pump.

Never allow the immersion pump to run

against a closed off pressure line.

When using in shafts, make sure the size is

adequate.

Always cover the shaft with a secure foot-

plate.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Al-ko 7500 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info