Bedienungsanleitung Al-ko GTE 450 (Seite 16 von 150) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

594615

Zoom out

Zoom in

Vorherige Seite

1/150

Nächste Seite

Safety instructions

16 GTE 350 / 450 / 550

Damaged or brittle extension cables must not

be used.

➯

Check the condition of your extension

cable each time you start to use the

equipment.

Secure the extension cable in the cable strain

relief.

Do not get the appliance wet or expose it to

moisture.

Keep children away from appliances connec-

ted to the mains.

ASSEMBLY

CAUTION!

The machine must not be put in opera-

tion before it has been assembled com-

pletely.

Install the guard plate

ADVICE

The knife integrated in the guard plate

automatically cuts the line to the opti-

mum length.

GTE 350

1. Set the guard plate in relation to the cutter

head (2-1).

2. Make sure that the line is exposed.

3. Secure with the enclosed 4 screws.

GTE 450, GTE 550

1. Set the guard plate in relation to the cutter

head (2-1).

2. Make sure that the line is exposed.

3. Screw the guard plate on at the rear with the

supplied screws (2-1).

4. Place the guide wheel on the guard hood and

tighten the screws (2.2).

Installation of auxiliary handle

GTE 350

1. Pull the grip bar of the auxiliary handle slightly

apart (3-1).

2. Push the auxiliary handle onto the holder

(3-2).

3. Engage the auxiliary handle in the splines.

4. Put on the pin holder and screw the clamping

pin tight (3-3).

GTE 450, GTE 550

The angle of the handle can be individually adjus-

ted using the tip lever.

1. Push the holder onto the shaft.

2. Pull the grip bar of the auxiliary handle slightly

apart (3-1).

3. Push the auxiliary handle onto the holder

(3-2).

4. Engage the auxiliary handle in the splines.

5. Place the tip lever with pin holder onto the

clamping pin.

6. Screw the clamping pin tight so that the tip

lever can be operated with little force (3-3).

STARTUP

CAUTION!

Always perform a visual check prior to

start-up.

Adjusting the telescopic handle

1. To release, turn the upper locking sleeve

through about 180° to the right (4-1).

2. Set the telescopic handle to the individual

physique. The telescopic handle can be ex-

tended by approx. 10 cm (4-2).

3. Tighten the locking sleeve (4-3).

Swivelling the cutter head

To trim lawn edges, for example, it is possible to

swivel the cutter head through 180° (5, 6).

1. Loosen the lower locking sleeve (5-1).

2. Turn the telescopic handle through 180° (5-2).

3. Screw the locking sleeve tight (5-3, 6-1).

Angling the cutter head

By changing the pivot angle, it is also possible to

trim areas that are difficult to access, e.g. under

benches, overhangs, etc.

1. Press the locking button (7-1).

2. Engage the cutter head in the required angle

(7-2).

3. Release the locking button.

ADVICE

Remove the guard on the line cutter be-

fore taking into operation for the first

time.

Starting the lawn trimmer

1. Guide the extension cable through the strain

relief.

2. Connect the extension cable to the mains

supply.

3. Stand securely.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Al-ko GTE 450 Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info