Bedienungsanleitung Al-ko Motorhacke AL-KO MH 5000 (Seite 13 von 88) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

601546

Zoom out

Zoom in

Vorherige Seite

1/88

Nächste Seite

GB 3 Translation of original user instructions

Engine Start

At engine start, clutch lever of weeder share

can’t be activated!

 Set-up saturator lever into position "START"

 Pull out quickly starter cable and afterwards,

let it slowly wind up!

Putting of Weeder Share into Operation

 Pull up clutch lever entirely and hold it.

Weeder share will begin to rotate only at the

second half of lever motion.

Breaking of Weeder Share

 Loose clutch lever.

If you will loose clutch lever, weeder share

can’t rotate!

Starting reverse drive

Never start the reverse drive while moving

forward. Danger of severe damages to the

machine!

 Pull up lever for reverse drive as far as it will

go.

Disconnection of reverse drive

 Release lever for reverse drive.

Engine Breaking

 Set-up saturator lever into position "STOP".

Maintenance

Before all Maintenance and Cleaning

Works Disconnect the Connector from

Spark Plug!

 Clean the machine after its utilization.

 Do not spray the machine with water. Water

in ignition device or in carburetor can pro-

voke troubles.

If the machine is inclined to its side, the

carburetor must be pointed upwards.

Professional Control is necessary:

 at abrupt engine stop

 at weeder share distortion

 at gearbox damage

 at V-belt pulley damage.

Refilling of Gear Oil

As a matter of principle, the gear oil should be

changed after 100 operating hours. (oil viscosity

SAE 80).

Oil change

Required oil amount:

 Type series 4000, 5000 approx. 0.5 l.

 Type MH 350-4 approx. 0.2 l.

 Loosen oil screw plug (Fig. 15).

 Fill new oil.

 The oil must be visible at the filling opening.

 Close feed opening by screwed drain plug.

Engine

Oil Refilling / Air Filter / Spark Plug

See – Operating instructions delivered by engine

producer.

Setting-up of Bowden cables

Fine setting-up is being made by means of an

adjusting screw on upper handle (Fig. 6 and 12)

and on engine support (on ends of Bowden

cables).

 Loose the safety nut.

 Set up by means of adjusting screw.

Correct Setting-up:

Weeder shares can begin to rotate only in the

second half of lever motion.

 Tighten the safety nut.

Gas Uptake

See – Operating instructions delivered by engine

producer.

Maintenance and storage

Before you start any work on the unit:

Switch the engine off, wait until the weeding

shares Stop; unplug the connector of the spark-

ing plug.

Wear protective gloves when manipulating the

weeding shares.

Never store the unit with fuel in the tank in build-

ings where fumes may reach an open flame or

spark

– risk of explosion!

The fuel tank is to be drained outdoors only.

Allow the engine to cool before storing it in the

locked up area.

Never squirt the unit with water.

All repairs shall be carried out by authorized

service dealers only.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Al-ko Motorhacke AL-KO MH 5000 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info