Bedienungsanleitung Al-ko TCS Duotec 3000 (Seite 16 von 52) (Deutsch, Englisch, Holländisch, Französisch, Italienisch)

601590

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

Power supply

16 456251_a

Do not deactivate safety and/or protective de-

vices of the machine.

Always ensure secure standing of the ma-

chine.

Never transport the shredder with the motor

running.

Switch the motor off, wait for the cutting disk

to stop moving, and disconnect the machine

from the mains connection prior to moving the

machine.

When moving the shredder, exclusively carry

the shredder on its handle.

Immediately disconnect the plug from the

mains if the extension cable has been dama-

ged or cut!

We recommend the connection via a earth le-

akage circuit breaker (ELCB) with a rated le-

akage current < 30 mA.

The mains voltage at your location must meet

the information regarding mains voltage in

the Technical Data. Do not use any other sup-

ply voltage.

The type of cable used should be 3 core dou-

ble insulated minimum of 1.5 mm to a maxi-

mum of 2.5 cross section to BS 6500 (1984)

tabel 16 PVC flex core. 300/500 V H05 W-F.

Any extension cable, up to a maximum of 50

m, should be of a type not lighter than the ca-

ble prescribed for the machine. The connec-

tor for the extension should be splash-proof.

Damaged or fragile extension cables may not

be used.

Check the condition of you extension cable

prior for every use.

Only use the mains connection for the desi-

gnated purpose. Do not pull the mains cable

in order to pull the mains plug out of the so-

cket. Protect the cable against heat and sharp

edges.

Always disconnect the shredder from the

mains connection when not in use.

Route the extension cable such that they do

not interfere and cannot be damage during

shredding.

Immediately switch off the shredder saw and

disconnect it from the mains connection if you

notice any changes.

Always ensure secure standing while

working. Do not bent forward to far.

Do not feed the shredder from an elevated

position.

POWER SUPPLY

The machine can be plugged into any 13 A mains

socket with 240 V ac, and must be protected by

a 13 A fuse. (TCS Duotec 3000: 400 V, Observe

correct direction of rotation)

Excluded from this are countries with a lower con-

nected load (10 A; 13 A, slowblowding).

WARNING!

Only for Great Britain (240 V)!

This machine must be earth!

Never use a faulty power cable!

Check the power cable regularly for

signs of wear and tear!

Wiring Instructions

When wiring the english 3 pin plug

please follow the instruction accor-

ding to the colour coding as shown

below:

Green and

Yellow to

terminal

E Earth

Brown to

terminal

L Live

Blue to

terminal

N Neutral

In accordance with VDE regulations, the machine

is fitted with a safety cutout switch which switches

off the power in the event of overload.

Overloading may occur if the blade is jammed for

a prolonged period of time. The safety switch is

designed to cause a delay of 1 - 3 minutes be-

for the motor can be restartet: Prior the restarting,

however the cause of overloading must be ascer-

tained and remedied.

To restart the motor, the switch must first be re-

turned to the OFF position, the after 2 or 3 minu-

tes the machine can be switched on again by swit-

ching the switch to ON.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Al-ko TCS Duotec 3000 Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info