Bedienungsanleitung Alber Scalacombi eco S34 (Seite 14 von 32) (Englisch)

785819

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

3. Operation on a staircase

During your initial instruction session, you have already learnt how to climb stairs with

the scalacombi. You also had the opportunity to complete your first climb under the

supervision of the authorised dealer or agent of Alber GmbH. Before transporting a per-

son on the scalacombi, you should, however, read the instructions below and practice the

individual steps with the empty stair climber on a staircase.

To safely transport a person, you might need to use a lap belt or foot belt (optional

accessories). It is the responsibility of the operator to check whether such equipment is

necessary.

3.1 Climbing up a staircase

•The passenger must take his/her place on the scalacombi while it is standing on firm

level ground.

•Ensure that the two drive wheels [5] and the brakes [4] are in pushing position (see

chapter 2.2).

•Check again that the person is properly seated on the scalacombi.

•If the scalacombi is not yet switched on, do this by actuating the ON/OFF button [8]

(see chapter 2.4).

•Tilt the scalacombi towards you until it is at an optimum angle so that the stair

climber with the passenger is well balanced. Maintain this angle during the entire

climb up the stairs.

•To tilt the scalacombi, you can place a foot against the panel between the two wheels

(see diagram to the left).

•Carefully move the scalacombi towards the stair until both wheels of the climber

touch the first step (see diagram to the left).

•To move up one step, press the driving switch [17] into its upper position and hold

it there until the first step has been climbed. Simultaneously pull the scalacombi

slightly towards you.

•After the first step has been climbed, the climbing function is automatically switched

off. You can now release the driving switch.

•The scalacombi is now standing on the outer edge of the first step of the staircase

and must be pulled by you towards the next step.

•Press the driving switch [17] again into its upper position and climb the next step.

•Repeat the above steps until all steps of the staircase have been climbed.

•After the last step has been climbed, move the scalacombi to a firm and level surface

(do not leave it at the edge of the step!).

•To do this, place the two drive wheels [5] and the brakes [4] in their pushing position

(see chapter 2.2).

•Switch the scalacombi off.

•The person transported up the stairs can now exit the stair climber.

If the driving switch [17] is released during climbing operation, the

wheels are immediately stopped in their position.

Do not release the driving switch when climbing up a step, unless in

an emergency situation (see chapter 3.4).

Use the scalacombi only on staircases that are not wet, waxed or

otherwise slippery. Ensure that carpets are properly secured to the

floor. The step height may not exceed 20 cm. The minimum step

depth should not be below 14 cm.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Alber Scalacombi eco S34 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Alber Scalacombi eco S34

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info