4. Using your Phone
4.1. Registration
If you buy the bundle package of the
pre-registered with the base of
In case the XS is not registered to a base, the LED of the XS is blinking RED, please follow the procedure below:
On the base of T
Put the base into registration mode. Please refer to details in user guide of the telephone.
On the
Long press simultaneously for 3 seconds on 2 keys, and , it will enter registration mode with a beep tone
emitted. During registration phase, the
A
if the XS is not in the cradle
Alcatel XS
USER’S GUIDE
Package contents:
The package contains the following items:
1. 1
2. 1 Charger
3. 1 Power adaptor
4. 1 Neck strap (pre-connected to
5. 2 x
6. 1 User
1. IMPORT
When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of
fire, electric shock and injury
1) Read and understand all the instructions.
2) Follow all warnings and instructions marked on the product.
3) Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a
damp cloth for cleaning.
4) Do not use this product near water (for example, near a bath tub, kitchen sink, swimming pool).
5) Do not expose the telephone to direct sunlight or extreme cold environment. Do not put the telephone close to a
heating source such as radiators, cookers, etc.
6) Do not overload wall outlets and extension cords as this can result in the risk of fire or electric shock.
7) NEVER use your phone outdoors during a thunderstorm-unplug the base from the telephone line and the mains
socket when there are storms in your area.
8) Do not use the telephone to report a gas leak in the vicinity of the leak.
9) Use only the supplied NiMH (Nickel Metal Hydride) batteries! The operation periods for the handsets are only
applicable with the default battery capacities.
10) The use of other battery types or non-rechargeable batteries/primary cells can be dangerous.
cause interference and/or unit damages. The manufacturer will not be held liable for damage arising from such
non-compliance.
1
12) Please note the correct polarity while inserting the batteries.
13) Dispose of batteries safely
punctured.
14) Risk of explosion if battery is replaced by an incorrect type.
2. INST
2.1 Connecting the base charger
2.2 Installing and charging the batteries
1) Slide down to open the battery compartment cover
2) Place the 2 supplied
extra attention to direction of polarity
3) Slide the battery compartment cover back.
4) Put the handset on the base and charge for 24 hours before using the
handset for the first time. The handset will give a beep when it is
properly placed on the charger
handset will give a beep.
Notes:
1) Use only the supplied NiMH rechargeable batteries.
2) If the handset will not be used for a long time, disconnect and remove
the batteries to prevent possible leakage.
Base Charger
If the
LED will blink in Red as described in table 1.
Note: Without correct registration of the
not POSSIBLE . Please refer to troubleshooting table.
4.2. Receive a call
When you receive a call, the blue LED blinks, you can take the call at any time during the ringing phase. T
answer the call, press the key to answer the call.
4.3. Make a call
Once the memories are configured, you can make a direct call to the preset memory
refers to table 1)
- Press and hold key for 3 seconds to dial memory M3
Or
- Press and hold key for 3 seconds to dial memory M1
Or
- Press and hold key for 3 seconds to dial memory M2
- The
- T
Remark: If no number has been preset, 2 beep tones are emitted indicating the memory is empty
4.4.
Y
and key during ringing phase.
There are 6 levels (level 1 to 5 and off)
! W
4.5.
There are 5 levels (VOLUME 1 to VOLUME 5) to choose from for each of headset and handsfree volume.
During a call, press key or key to select volume 1-5. When you end the call, the setting will remain at the
last selected level.
4.6. Barge in a call / Call transfer
Function is enabled for the limited bundle package (XS + V
When your telephone (V
pressing key of the XS.
Then, when you end the call using the XL
the call to the XS automatically
4.7. End a Call
During a call connection, press either key OR put the
4.8. Intercom
Y
handset manual.
5. Phone settings
Y
to work.
Use your mobile phone to dial in the telephone number that
the
Then, your mobile phone are in communication with the
T
When entering the key using your mobile phone keypad, the LED of
setting mode is entered now
It is advised to set your mobile phone in mute mode for avoiding any acoustic interference with
handset during setting of your
Example for programming the Memory M1 or M2 or M3:
When the communication mode is set up, press key on the keypad of your mobile phone. The
turns on blue. Press 2 digits (0 and 1) for programming the Memory 1 or digit (0 and 2) for the memory 2 or digit (0
and 3) for the memory 3.
Then enter the number from the keypad of your mobile phone to edit the memory number
T
In case of mistake in the entry
with key without releasing the communication mode.
In case of error in the command a double beep error tone is emitted after entering key #. In that case, resume the
command by entering key .
During the preset of the Ringer volume and MelodyThe
digit selection must be entered when the melody is ended.
WAlways press key again to disconnect
complete your settings.
Speaker
T
LED status
indicator
V
Memory 1
V
Memory 2
Micróphone
Headset
jack
3. GETTING TO KNOW
3.1. Overview of the Handset
Remove the film before use
DC plug from
adaptor
Charge
contact
