Bedienungsanleitung Alecto COA1910 (Seite 40 von 68) (Deutsch, Englisch, Holländisch, Französisch)

794845

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

INSTALLATION:

1. Insert the included batteries into the detector.

A. Turn the securing pins inward

B. Insert the 3 AA batteries, observing polarity.

(High Energy Alkaline batteries 1.5V AA - LR6)

C. The power, fault and alarm LEDs will light up for 0.5 seconds and

the detector will emit a short audible signal.

2. Push the latch out of the mounting plate.

3. Install the mounting plate on a suitable spot

4. Use the included plugs and screws.

5. Youcanperformthersttestbybrieypressingthetestbutton,

see also paragraph “Testing”.

6. Now interlock the mounting plate with the CO detector by inserting the

latch on top into the hole until you hear a click.

7. The CO detector is now functional.

USE:

1. Every45seconds,thepowerLEDlightsbrieytoindicatethatthedetectorisoperating.

2. Whenthedetectorgivesashortbleepevery60secondsandtheyellow“Fault”LEDashes,the

batteries should be replaced as soon as possible. At the start of these warnings, the detector will

operate for 30 days standby or 4 minutes in alarm mode.

3. The table below shows when the detector will sound the alarm.

CO concentration NO ALARM

for

ALARM

for

30PPM 120 min. -

50PPM 60 min. 90 min.

100PPM 10 min. 40 min.

300PPM - 3 min.

In accordance to the EN50291 standard.

4. When the alarm sounds, it will turn off within 6 seconds after moving the detector to a space with a CO

concentration below 40PPM.

5. The alarm sound can be turned off for up to 10 minutes by pressing and holding the TEST button for 3

seconds (<200PPM).

6. The detector will automatically perform a fault inspection every 180 seconds.

TESTING:

When the CO detector is operating under normal conditions, the sensor and siren should be tested at least

every month. Press the “TEST” key. “POWER”, “FAULT” and “ALARM” LED light up. Then the detector

gives 5 beeps within 10 seconds and also the red “ALARM” LED lights up. Everything is now ok.

If the detector gives an error message, the yellow “FAULT” LED will light 2 times and give 2 beeps per

minute.

SILENCING ALARM (HUSH FUNCTION):

Sometimesthealarmmaygooffduetoinuenceofenvironmentalfactors.Forexample,smokecontaining

certain concentrations of carbon monoxide or other chemical gases. When the CO level is lower than

200PPM, you can press the “TEST” button. The alarm will stop and the detector will immediately check the

CO value again. When the concentration is higher than 200PPM it is impossible to stop the alarm.

The red LED will blink 8 times per second- and the sound signal will stop for max 10 minutes. If after max

- AA +

+ AA -

- AA +

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Alecto COA1910 Seite 40

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info