Bedienungsanleitung Alecto DKW-2012 (Seite 4 von 13) (Englisch)

617339

Zoom out

Zoom in

Vorherige Seite

1/13

Nächste Seite

- 4 -

data transmission happened, the LED will be on for 20ms. During radio controlled time reception period,

there is no transmission and normal transmission will only resume after time reception routine is

complete. The longest time for radio controlled time reception is 5 minutes.

Receiver /Indoor unit

After inserting the batteries into the Weather Station, all LCD segments will be turned on for a few

seconds, all possible display segments are turned on for checking.

After this, the weather station will make initial measurement and start to register the transmitter (the

radio reception icon will be turned on). Do not press any key before outdoor sensor data received,

otherwise the outdoor sensor learning mode will be terminated. When outdoor transmitter has been

registered, the base station will automatically switch to the normal display mode from which all further

settings can be performed by the user.

If no RCC signal is detected in the initial setup, the transmitter will try once every two hours to get an

RCC signal until a signal is received. Once the transmitter receives the RCC signal it will transmit the

signal to the monitor. On the monitor the RCC tower icon will be displayed, if the monitor doesn’t receive

the RCC signal or loses the signal continuously for 12 hours the RCC icon will not be display.

Note for RCC signal:

The best condition for reception is at night, between midnight and 6:00am – when there is less

atmospheric interference.

Note:

If a battery change on the transmitter side happened, the receiver will be resynchronized to the

transmitter again within the next 3 hours. If you want to shorten the receiving data time, the base station

has to re-install the battery so that it can have the new security code learnt right way, but the previous

weather data and alarm value settings in receiver will be lost.

Note:

Commonly the radio communication between receiver and transmitter in the open field can reach a

distance of up to 330 feet providing that there are no interfering obstacles such as buildings, trees,

vehicles, high voltage lines, etc.

Radio interferences such as PC screens, radios or TV sets can, in bad cases, entirely cut off radio

communication. Please take this into consideration when choosing standing or mounting locations.

Mounting

Before placing and installing all components of the weather station at there final destination, please set

up the weather station with all parts being nearby for testing the correct function. If e.g. there appear to

be problems with the 433 MHz radio transmission, they can mostly be overcome by moving the

mounting locations.

Transmitter (thermo-hygro sensor), rain collector, wind direction sensor have been mounted onto the

mast. You just need to assemble the wind cups attached.

Attaching the Wind Cups

1. Push the wind cups onto the anemometer’s stainless steel shaft.

2. Use the Allen wrench provided to tighten the set screw on the side of the wind cups.

3. Spin the wind cups. If the wind cups spin freely, the anemometer is ready and can be installation.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Alecto DKW-2012 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Alecto DKW-2012

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info