INST
BABY UNIT
Power:
1. Connect one of the supplied 5V power adaptors to the 5V
DC input of the baby unit.
2. Insert the adapter into a 230V wall socket.
Only use the supplied power adaptor
Make sure that the baby can’t
touch the wire of the baby unit.
Place the baby unit at least
1-1.5 meters away from the baby
and bundle excess cable lengths
using tape or cable-ties specically designed for this purpose.
T
Y
or suspend it from a wall.
For wall mounting:
Drill two holes in the wall, next to each other and at a distance
from 2.1cm, then insert plugs and screws. Leave the head of
the screw protrude for several millimeters.
Suspend the baby unit by sliding the recesses in the camera
support over the screws in the wall and then pressing the
baby unit somewhat downward. Finally
tor cable using cable-ties.
Tips for placement:
• For use as a baby monitor: place the baby unit at least
1-1.5 meters away from your baby and make sure to
safely tuck away the adapter cable.
• The temperature protrudes from the rear of the baby unit.
Make sure this sensor hangs freely
sunlight and avoid heat from e.g. light bulbs.
parent unit switched off and power adaptor connected:
• orange light while the battery is being charged
• green light remains lit when the battery is fully charged
10.
abled
1
12.
13.
14-17. , , and buttons
18.
19.
BABY UNIT
20. Antenna
21.
and disabling the night
view LED’s
22.
23.
infra-red LED’s for the
night view lighting (not vis-
ible to the naked eye)
24.
25.
and accurately orientate
the baby unit
26.
27.
28.
29.
ter (or re-register) the baby
unit on the parent unit
30.
SYMBOL
While using the parent unit, the following symbols may appear
in the display:
In the upper left corner
strong reception
good reception
average reception
and poor reception
no reception
When talking to the baby
side of the antenna symbol will illuminate.
CAM1
In the upper right corner
watching is indicated. When multiple cameras are connected
to the parent unit and you’ve enabled the scan function (to
automatically switch to the next camera screen every 10 sec-
onds), also the symbol will appear
Next to the camera indication, the battery capacity is shown:
battery full
battery 3/4 full
battery 2/4 full
battery 1/4 full
the outline is red and ashing: the battery is nearly ex-
hausted and the parent unit may switch off at any moment
no battery inserted or the battery is not connected. While
charging, the battery symbol keeps scrolling until the battery is
fully charged.
While adjusting the volume, the current volume level
is shown in the right side of the display
volume level is set to 0 (sound off), the ‘no sound’
icon will appear here.
When the volume is turned off, the symbol appears in the
upper part of the display to remind you that you’ve switched
off the sound.
Press the button to open the
menu. Y
of these functions further in this manual.
illuminates when the temperature alert is enabled. This
symbol starts ashing when the set limit is exceeded.
USE
The functions ‘Brightness’, ‘Lullabies’, ‘Multi-camera’,
‘Zoom’, T
(screen and sound switch off automatically when the baby is
sleeping) are described on the other side of this user
underneath the header ‘MENU-OPERA.
BABY UNIT
Switching on/off:
Slide the ON/OFF switch at the rear to the ON position to turn
on and slide to the OFF position to turn off.
underneath the ON/OFF switch illuminates several seconds
after you’ve switched on the unit.
Automatic night vision:
The baby unit is provided with built-in infra-red LEDs; these
LEDs will switch on automatically when the baby room turns
dark and will switch of again when it becomes light.
The LEDs can illuminate objects up to a distance of
approximately 2 meters.
When it’s dark, that is when the night vision LEDs
are switched on, the images on the parent unit will be
displayed in black and white.
Attention: infra-red light cannot be perceived by the
human eye; that means you cannot tell whether the
infra-red LEDs are switched on with the naked eye.
P
Switching on/off:
press and hold for 2 seconds to turn off
V
Use the + and - buttons to set the loudness of the sounds
from the baby room that you hear through the speaker of the
parent unit.
While adjusting, the volume level will be indicated on the display
T
When the screen is enabled, press the button to talk to
your baby
talking and release the button to listen.
Sound indicators:
In the middle of the upper part of the display you’ll nd 4
sound indicators indicating whether the baby is crying by
ashing. This allows you to watch over your baby when the
sound is set to a low level or is turned off, or when the baby
monitor is placed a bit further away in the room.
Automatic on/off function: (VOX)
When the baby is sleeping quietly or when the baby unit is not
picking up any sounds, you may have the display and sound
of the parent unit switch off automatically and back on again
as soon as the baby starts crying.
The sensitivity of the automatic on/off function can be adjusted
(see chapter MENU further in this user
VOX push-button to enable or disable this function; the VOX
indicator shows whether this function is enabled or disabled:
light off = VOX function of
(the images and sound are
transmitted continuously)
light on = VOX function on
(display and sound off while the
baby is sleeping)
T
By briey pressing any button you may enable the display and
sound again for a short time to watch and listen to the baby
After several seconds, the display and sound are turned off
again.
Battery weak (empty) notication:
When in use, the battery symbol in the upper right corner of
the display shows the battery capacity
As soon as the battery capacity falls below 25%, the red
power LED will illuminate to inform you of this. It’s now recom-
mended to connect the adaptor to recharge the battery
When the battery capacity further decreases to nearly empty
this red battery symbol starts ashing. -
tor starts ashing in red and every 30 seconds several alert
tones are emitted for 10 to 15 minutes long. Now immediately
connect the adaptor otherwise the parent unit will switch itself
off within this time period.
USER’S MANU
D
INTRODUCTION
• The
tion system, suitable for private use indoors.
• Y
have the baby monitor switch on.
• The
and other provisions as described in the European Direc-
tive 1999/5/EC.
• The declaration of conformity is
available on the website www
alecto.nl
• Use of this equipment is allowed in all countries of the
EU. In France, Italy
is allowed.
A
Before you start using the set, please remove any protective
foil from the parent unit and baby unit.
About this user
This symbol represents a warning. T
always adhere to the instructions described in this
documentation.
This symbol is followed by a user
Always check the
this user
FUNCTION O
P
1. Battery compartment (rear)
2. Power adaptor input
3. VOX on/off button
4. ENTER button for menu settings
5. MENU button
6. T
7. Power on/off button
8. Built-in microphone
9. Power indicator:
parent unit switched on, power adaptor not connected:
• green light during normal use
• red light when the battery capacity is low
• ashing red light when the parent unit may switch off at
any moment due to a low battery capacity
parent unit switched on and power adaptor connected:
• ashing green light while the battery is being charged
• green light remains lit when the battery is fully charged
• For optimal range, it is advisable to set up the baby unit as
high as possible, free from large metal surfaces.
The baby unit is not waterproof and therefore suit-able
for indoor use only
P
Battery:
1. Open the battery compartment by sliding and clicking off
the battery cover at the rear
2. Connect the battery plug in the battery compartment ac-
cording to the gure below and install the battery
3. Click the battery cover back onto the parent unit.
Never connect the plug or install the battery by force.
Only install the supplied rechargeable Li-ion battery (3.7V
1440mAh).
Power adapter:
1. Connect the other 5V power adapter on the left side of the
parent unit.
2. Insert the adapter into a 230V wall socket.
The battery starts charging as soon as you connect the power
adaptor
battery for at least 15 hours, even when the indicator shows a
fully charged battery
Only use the supplied power adaptor
General:
Fold out the support at the rear to place the parent unit onto a
table or cabinet.
Keep the antenna of the parent unit in an upright position for
optimal range.
The parent unit is not water-proof, hence is only suitable
for indoor use.
20
22
23
25
24
21
28
29
30
27
26
6
5
4
7
3
14
15
16
13
17
VOX
8 9 10 11 12
2
18
1
19
1-1.5m
VOX
VOX indicator
