Bedienungsanleitung Alecto DVM 50 (Seite 29 von 36) (Deutsch, Englisch, Holländisch, Französisch)

803225

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

3 INSTALLATION

3.1 BABY UNIT:

Power:

1. Connect one of the included 6V power adapters into the 6V DC socket of the baby unit.

2. Plug the power adapter into a 230V electrical outlet.

Only use the supplied power adapter model number 5E-AD060080-E.

When used as a baby monitor: Make sure the baby cannot touch the baby monitor or the

cord. Place the baby unit at least 2 meters away from the baby and tape up any additional

long wires with tape or special wire ties.

Wall mounting:

Drill two holes next to each other in the wall 6.7 cm apart and insert two screws. Leave the screw head

out by a few millimetres.. Hang the baby unit on the wall by sliding the notches on the camera stand

down onto the screws. Tie the adapter cord neatly up with special wire ties.

Placement tips:

• When used as a baby monitor, place the baby unit a minimum distance of 2 meter away from your

baby and make sure the power adaptor cord is safely tucked away.

• For an optimum connection range, it is preferred to set the baby unit as high as possible and away

from large metal surfaces.

3.2 PARENT UNIT:

Power:

The parent unit can be powered directly from the supplied rechargeable battery, or the included power

adapter. When you connect the power adapter it will also charge the battery so that the parent unit can

be used cordless.

Battery:

1. Open the battery compartment by sliding the battery cover on the back off.

2. Connect the plug in the battery compartment and insert the battery according to the illustration.

3. Slide the battery cover back onto the parent unit.

Connecting the plug and inserting the battery without force.

Only insert the supplied rechargeable Li-ion Polymer battery (3.7V,1500mAh).

Power adapter:

1. Connect the 6V power adapter to the other 6V DC socket located on the side of the parent unit.

2. Plug the adapter into a 230V electrical outlet.

Use only the supplied power adapter model number 5E-AD060080-E.

Make sure that the power adapter cord cannot cause any tripping or falling. Tie up any long wires with

tape or special purpose wire ties.

Charging:

The battery will begin charging once you have connected the parent unit to the power adapter and

then the other end of the adapter into a 230V electrical wall outlet.

• Thebatteryneedstobechargedforatleast15hoursbeforeusingitthersttime,evenifthebat-

tery indicator shows fully charged.

• The charging circuit of the battery is electronically controlled so there is no danger of overcharging.

You can leave the power adapter permanently connected.

• If you are not using the set for long periods of time (> 2 months), it is advisable to take the adapter

out from the electrical wall outlet and remove the battery from the parent unit. When you begin

usingitagain,rstchargethebattery.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Alecto DVM 50 Seite 29

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info