Bedienungsanleitung Alecto DVM-67 (Seite 1 von 2) (Englisch)

668915

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

INTRODUCTION

The Alecto DVM-67 is a wireless audio/video baby monitor,

suitable for private use indoors.

You can either watch and listen continuously or you can have

the baby monitor switch on automatically as soon as your

baby starts crying.

The Alecto DVM-67 meets all essential requirements and

other provisions as described in the European Directive

1999/5/EC.

The declaration of conformity is available

on the website www.alecto.nl

Use of this equipment is allowed in all countries of the EU. In

France, Italy, Russia and Ukraine, only indoor use is allowed.

ATTENTION

Before you start using the set, please remove any protective

foil from the parent unit and baby unit.

ICONS ON THE DISPLAY

upper part of the display, during normal use

indicates the reception strength:

strong reception

good reception

average reception

bad reception

receiver is searching for a camera

no camera detected

(x = 1 ~ 4) shows which camera you are viewing

‘monitoring mode’ (setup choice to view cameras one after

the other when using multiple cameras)

volume set to 0 (speaker turned off)

VOX is activated (unit switches on automatically when the

baby starts crying)

temperature display of the baby room

battery indication:

battery is empty

battery is full

animation while the bat-

tery is charging

appears when the adaptor is connected and the battery is

not or incorrectly installed

icons on the display during setup

this icon is followed by the number of registered cameras

which you can select using the and buttons

in this menu, you can set the display brightness

here you can set the sensitivity level for the VOX function

in this menu, you can turn the VOX function on or off

here you can choose to have the temperature shown in

degrees Celsius or degrees Fahrenheit

in this menu, you can register additional cameras on the

receiver

INSTALLATION

BABY UNIT:

Power:

1. Connect one of the

supplied 6V power

adaptors to the 6V

DC input of the baby

unit.

2. Insert the adapter into

a 230V wall socket.

Only use the supplied power adaptor with model number

S003IV0600060.

Wall-mounting:

Drill two holes next to each other in the

wall separated by a distance of 5.4cm

and insert plugs and screws. The head

of the screw should stick out of the wall

for several millimeters.

Slide the foot of the baby unit over the

screws and then press the baby unit a

little downwards.

Tips for placement:

• For use as a baby monitor:

place the baby unit at least

1-2 meters away from your

baby and make sure to safely

tuck away the adapter cable.

• For optimal range, it is advis-

able to set up the baby unit

as high as possible, free from large metal surfaces.

• The temperature protrudes from the rear of the baby unit.

Make sure this sensor hangs freely, unexposed to direct

sunlight and avoid heat from e.g. light bulbs.

• The baby unit is not waterproof. When using outdoors,

make sure to protect the baby unit against moisture and

sand.

PARENT UNIT:

Power supply:

The parent unit can be powered directly by the included re-

chargeable battery or via the supplied power adapter. As soon

as you connect the power adapter, it will charge the battery

allowing for mobile use of the parent unit.

Battery:

1. Open the battery com-

partment by sliding and

clicking off the battery

cover at the rear.

2. Connect the battery

plug in the battery

compartment according

to the gure below and

install the battery.

Only install

the supplied

rechargeable NiMH bat-

tery (3.6V, 900mAh).

Never connect the plug

or install the battery by

force.

3. Click the battery cover

back onto the parent

unit.

Power adapter:

1. Connect

the other

6V power

adapter to

the DC6V

input on the

side of the

parent unit.

(behind the

rubber cover

top)

2. Insert the adapter into a 230V wall socket.

Only use the supplied power adaptor with model number

S003IV0600060.

You can recharge the battery with the parent unit either

switched on or off, although charging the battery with the

parent unit switched off will take less time.

Charging:

The battery will be charged as soon as you connect the power

adapter and insert it into a 230V wall socket.

• For initial use, charge the battery for at least 15 hours,

even if the indicator shows a fully charged battery.

• The charging circuit for the battery is managed electroni-

cally and there is no risk of overcharging, this allows you

to leave the adapter connected at all times.

• In case you will not use the set for a longer period of time

(>2 months), please make sure to disconnect the adapter

from the wall socket and remove the battery from the par-

ent unit. When starting to use the set again, make sure to

properly charge the battery.

• Make sure nobody can trip or fall over the adapter cable.

You can bundle cables that are too long with tape or

cables ties available specically for this purpose.

Battery indication:

Upper part of the display: (only with the parent unit switched

on)

• : no battery installed, parent unit is powered directly

through the adaptor

• : battery is full

• : battery is nearly empty

•

: battery is charging

Middle part of the display: (only with the parent unit switched

on)

• : this symbol appears for several seconds every minute

in the last hour before the battery is exhausted.

Indicator on the parent unit:

• ashes in red: battery nearly empty

• remains red: battery is charging (turns off when the bat-

tery is full)

Lanyard:

You can attach a lanyard

or wristband at the top of

the parent unit. A lanyard or

wristband is not included.

USER MANUAL

DVM-67

PARENT UNIT:

1. visual sound indica-

tion, also displays the

volume level while

adjusting

2. power button, press

briey to turn the

display on or off,

press and hold for

2 seconds to turn the

parent unit on or off

3. battery indicator (see

also further in this

user manual)

4. power adaptor input

5. zoom in/out,

6. power indicator

7. function button:

MENU/SELECT:

to open the menu and

to conrm selections

VOL , VOL , and

: various functions,

see this user manual

8. talk-back button to-

wards the baby unit

9. built-in microphone

10. Battery compartment

11. suspending option for

wrist band

12. built-in speaker

13. foldable stand

FUNCTIONS OVERVIEW

BABY UNIT:

1. Infra-red LEDs

(for night vision)

2. indicator light,

switched off when

the baby unit is

turned off, ashes

while the baby

unit is searching

for the parent

unit, remains lit

when the baby

unit is in commu-

nication with the

parent unit

3. power adaptor

input

4. power button

5. light sensor

6. camera lens

7. Volume increase

8. PAIR button (to

pair this baby unit

with the parent

unit)

9. Volume decrease

10. built-in micro-

phone

11. Built-in speaker

12. Temperature

sensor

13. Ball coupling

hinge for proper

camera orienta-

tion

14. camera feet

>1 - 2 m

Alecto DVM-67 Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Alecto DVM-67

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info