Bedienungsanleitung Alecto DVM-700 (Seite 44 von 52) (Deutsch, Englisch, Holländisch, Französisch)

668917

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

• This ‘Cry Alert’ warning consists of a warning in the display and you may also

set the following (see the tab ‘Cry Alerts’):

1. Beep & Vibrate: beep tone + vibration

as an extra warning

Vibrate: only vibration as an extra

warning

Beep: only a beep tone as an extra

warning

Screen only: only a warning in the

display

2. This setting has no function

• example of a warning when the baby is crying:

- the alert stops automatically after 30

seconds or you may press ‘Dismiss’ to stop

the alert beforehand

- touch ‘Settings’ to open the menu directly

and then set the alarm

To set the level at which the video and audio of the receiver are enabled again, go

to the tab Menu – Cry Alerts – VOX Sensitivity.

Off: VOX disabled, video and audio are transmitted continuously

Low: low sensitivity, the bay must be crying loudly before the receiver is switched on

Mid: average sensitivity, the receiver is switched on when they baby is crying

normally

High: high sensitivity, the receiver is switched on even when the baby is crying softly

4.6 SYSTEEM SETUP:

You may use the touch-screen of the parent unit to adjust the system settings of

the baby monitor.

1. touch the screen in a random spot, touch Menu and then touch Settings

1a 1b 1c

Cry alert: (VOX function)

You may continuously watch/listen to your baby or only when the baby is crying

as follows:

Watch/listen continuously:

1. touch the screen in a random spot, touch Menu and then touch Cry Alerts

2. now touch VOX sensitivity and select Off

Press the Home button to exit the menu and to return to the standard display. The

video and audio are now active at all times.

You can still enable or disable the video by pressing the Screen On/Off button

and you may adjust the volume level using the – Vol. + button

VOX controlled watching/listening:

1. touch the screen in a random spot, touch Menu and then touch Cry Alerts

2. now touch VOX sensitivity and select Low, Med or High

Press the Home button to exit the menu and to return to the standard display.

Operation:

• When the baby is sleeping quietly, the video and audio will be switched off

(you can always enable the video/audio by briefly pressing the Screen On/Off

button; the video and audio will be switched off again after several seconds)

• As soon as the baby starts crying, the video will be switched on. Provided the

volume isn’t set to level 0, the audio will be switched on as well so you can see

and hear your baby. After the baby goes back to sleep again, it’ll take 10 to 15

seconds until both video and audio switch off.

• If the volume is set to level 0 but the baby is making little noise, only the

display will switch on. If the baby is crying loudly (so loud that also the red

lights on the left side of the display are illuminated, see paragraph 2.4, item 7),

the display will switch on while you also get the ‘Cry Alert’ warning.

1a 1b 1c

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Alecto DVM-700 Seite 44

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info