Bedienungsanleitung Alecto FR-135 (Seite 1 von 2) (Englisch)

708470

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

USER’S MANUAL

INTRODUCTION

The Alecto FR-135 is a PMR-446 walkie-talkie.

This walkie-talkie allows you to not only com-

municate with each other free of charge, but also

with other (Alecto) walkie-talkies provided they

meet the PMR-446 standard.

DECLARATION OF CONFORMITY

I, Hesdo, hereby declare that the type of radio

equipment Alecto FR-135 conforms to Directive

2014/53/EU. The full text of the EU declaration

of conformity is available at the following internet

address:

http://DOC.hesdo.com/ FR-135-DOC.pdf

About this user’s manual:

This symbol represents a warning. To

ensure safe use, always adhere to the

instructions described in this documenta-

tion.

This symbol is followed by a user’s tip.

Always check the Alecto website for the most

recent version of this user’s manual. See the ver-

sion number at the back of this user’s manual.

FUNCTION OVERVIEW

/ button press and hold to switch the

walkie-talkie on or off briefly

press to transmit a calling alert

tone

button briefly press to switch the flash-

light on or off

/ button press and hold to lock the key-

pad briefly press to enter the

settings menu

/ button press and hold to switch on the

monitoring function (release this

button to disable the function

again) briefly press to switch the

channel scan on or off

button to increase or decrease the

reception volume and to select

the desired option during setup

DISPLAY

= set transmission channel

= set subchannel

= 2-channel scan is activated

= scan function is activated

= VOX

= battery indicator

= volume set to level 0 (no sound)

= keylock enabled

= ‘send’ indication / = ‘receive’ indication

INSTALLATION

POWER:

The FR-135 is powered through the included

rechargeable NiMH battery pack, size 3x AAA,

voltage 1.2V.

1. First remove the belt clip by pressing the

retaining clip backwards and then press the

belt clip upwards out of the walkie-talkie.

2. Now open the battery compartment by press-

ing the tab at the bottom of the battery cover

to up, the battery cover can then be removed.

3. Install the batteries according to the markings

in the battery compartment.

4. Replace the battery cover onto the walkie-

talkie.

5. Finally, slide the belt clip back onto the walkie-

talkie.

CHARGING:

Insert the small low-voltage plug of the power

adaptor into the rear of the charging station en

plug the adaptor into a 230V 50Hz wall socket.

Place the walkie-talkies into the charging station

to recharge the batteries.

The battery icon in the upper right corner of the

display scrolls while charging ( - - - )

You may also recharge the batteries by inserting

the small low-voltage plug of the power adaptor

directly into the right side of the walkie-talkie.

You may keep the walkie-talkies switched on

while charging.

REGULAR BATTERIES:

You may also install normal, non-recharge-

able 1.5V AA batteries, but these cannot be

recharged.

When using regular batteries, NEVER con-

nect the walkie-talkie to the charger or

power adaptor.

HEADSET:

On top of the FR-135 you’ll find the connection

for a headset with a 2.5mm plug. We advise you

to use an Alecto FRH-10 headset for this.

USE

Attention: for a connections between 2

walkie-talkies, both walkie-talkies must

be set to the same channel, with the same sub-

channel. See further on in this manual how to set

the channel and subchannel.

TO SWITCH ON/OFF:

Press and hold the button for 3 seconds to

switch the walkie-talkie on or off.

VOLUME CONTROL:

Repeatedly and briefly press the or button

to adjust the volume.

At volume level 0 (no sound), the icon appears

in the display.

TO TRANSMIT:

Press the button on the left side of the walk-

ie-talkie to transmit. Keep this button depressed

while speaking. Talk at a normal voice volume

and approximately 3 to 5 cm from the walkie-

talkie’s microphone.

While transmitting, the send indicator appears

in the display.

TO RECEIVE:

Release the button to receive.

While receiving a signal, the receive indicator

appears in the display.

CALL ALERT TONE:

Press the CALL button briefly to transmit a call

alert tone. This call alert tone is adjustable, see

‘To change the call alert tone’ further on in this

manual.

BACKGROUND LIGHTING:

Each time you press a function button (except

the button , / or ) the background

lighting of the display will illuminate. This light-

ing will automatically switch off 10 seconds after

pressing the last button

FLASH LIGHT:

Use the LAMP button to switch on the built-in

flash light.

Press the LAMP button again to turn the light off.

This function can also be used with the walkie-

talkie switched off.

Attention: never stare directly into the shin-

ing light nor point it at other people’s eyes.

The light can be bright and cause eye damage.

ADDITIONAL FUNCTIONS

KEYPAD LOCK:

When the keylock is enabled, the , , MENU

and SCAN buttons are blocked.

1. Press and hold the button until after approx.

3 seconds ‘ ’ appears in the display

2. Press and hold the button again for 2 sec-

onds to unlock these buttons

VOX FUNCTION:

When the VOX function is enabled (VOX = Voice

Activated Transmission), the FR-135 starts send-

ing as soon as you speak into the microphone.

To switch the VOX function on/off:

1. Press 3x the MENU button, the word “VOX”

will illuminate in the left part of the display

2. Use the buttons or to set the trigger sen-

sitivity (‘OF’ is off, ‘1’ is the lowest sensitivity,

‘3’ is the highest sensitivity)

3. Press the button to confirm

Preferably, use this function in combination with

headsets. Keep in mind that it can take over a

second after you’ve started talking before the

walkie-talkie enables the transmitter.

CHANNEL MONITORING: (listening)

Use this function to disable the noise reduction,

allowing you to also listen to weak transmitters on

the current channel.

1. Press and hold the MON button for 3 seconds

to disable the noise reduction and to monitor

the channel.

2. Release the MON button to turn the noise

reduction on again.

CHANNEL SCAN:

Use the scan function to listen in on all channels

one after the other.

1. Briefly press the SCAN button to start scan-

ning.

2. Briefly press the or button to continue

scanning if you’re only receiving noise on a

certain channel.

3. When the reception of the same channel

keeps failing during the scan, you may remove

this channel from the scan by pressing and

holding the or button for 2 seconds. The

scan will resume, but the selected channel will

be skipped.

• Attention, you cannot remove a channel to

which the walkie-talkie was set when the

scan was started.

• The next time you initiate a channel scan,

all channels will be scanned again.

4. Press the SCAN button again to end the scan.

FR-135

Charging contacts

(rear)

Microphone

Speaker

display

Flashlight

Headset

connection

Antenna

Send

button

Micro

USB port

for direct

charging

Alecto FR-135 Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Alecto FR-135

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info