Bedienungsanleitung Alecto FR-175 (Seite 1 von 2) (Englisch)

707356

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

USER MANUAL

INTRODUCTION

The Alecto FR-175 is a PMR-446 walkie-talkie.

This walkie-talkie allows you to not only commu-

nicate with each other free of charge, but also

with other (Alecto) walkie-talkies provided they

meet the PMR-446 standard.

Hereby, Hesdo declares that the radio equip-

ment type Alecto FR-175 is in compliance with

directive 2014/53/EU. The full text of the EU

declaration of conformity is available at the

following internet address:

http://DOC.hesdo.com/FR-175-DOC.pdf

DISPLAY FUNCTIONS

VOX = Voice Controlled Transmitting

SCAN = Channel Scan

Channel number

CTCSS subcode

= Standby

Battery level = receiving

= Sending

Key lock

Set volume level

FUNCTIONS INSTALLATION

POWER:

The FR-175 is powered through the included

rechargeable NiMH battery pack, size 3x AAA,

voltage 3.6V or through the 3x AAA penlite bat-

teries (excl.). If you choose to insert individual

rechargeable batteries, you must charge them

in a separate charger. The charging station sup-

plied with the FR-175 is only suitable for charg-

ing the included battery packs.

1. First remove the belt clip by pressing the

retaining clip backwards

and then press the belt clip

upwards out of the walkie-

talkie.

2. Now open the battery

compartment by pressing

the tab at the bottom of the

battery cover upwards, the

battery cover can then be

removed.

3. Insert the battery pack (the

charging contacts must

remain visible and the “UP”

arrow must point to the top

of the walkie-talkie.

4. Close the battery compartment, make sure

it’s closed properly and slide the belt clip

back onto the walkie-talkie.

The battery pack is provided with a small

strap to easily remove it. Make sure that

this strap, when replacing the rear cover, does

not cover one of the charging contacts at the rear

of the battery pack. Confirm this by placing the

walkie-talkie into the charger, the charging indica-

tor must then illuminate. Also see below.

CHARGING:

Insert the thin low-voltage plug into the side of the

charging station and plug the adapter into a 230V

50Hz wall socket. Place the walkie-talkies into the

charging station to recharge the batteries.

The indicators on the charger will illuminate

to indicate that the battery packs are being

recharged. These indicators remain lit, also when

the battery packs are fully charged. There’s no

risk of overcharging because the charging current

is electronically limited.

You may leave the walkie-talkies enabled while

charging them.

NORMAL BATTERIES:

Insert normal or rechargeable individual

batteries according to the drawing inside

the battery compartment.

When using normal batteries,

you may still place the

walkie-talkies into the charger.

However, the charging indica-

tors won’t illuminate and the

batteries will not be recharged.

When using rechargeable batteries, you must

recharge them in an external charger.

HEADSET:

On top of the FR-175 you’ll find the connector

for a headset with a 2.5mm plug. We advise you

to use an Alecto FRH-10 headset for this.

USE

Attention: for a connections between 2

walkie-talkies, both walkie-talkies must

be set to the same channel, with the same sub-

code. See further on in this manual how to set

the channel and sub-codes.

TO SWITCH ON/OFF:

Press and hold the button for 2 seconds to

switch the walkie-talkie on or off.

VOLUME CONTROL:

Repeatedly and briefly press the or button

to adjust the volume. The set volume level is

shown in the lower part of the display.

TO SEND:

Press the P button to send. Keep this button

depressed while speaking. Talk at a normal

voice volume and approximately 3 to 5 cm from

the walkie-talkie’s microphone.

TO RECEIVE:

Release the P button to receive.

CALL ALERT TONE:

Press the P button briefly to transmit a call alert

tone. This call alert tone is adjustable, see ‘To

change the call alert tone’ further on in this

manual.

BACKGROUND LIGHTING:

Each time you press a function button (except

the flash light button) the background lighting of

the display will illuminate. This lighting will auto-

matically switch off 10 seconds after pressing

the last button

FLASH LIGHT:

Use the button to switch on the built-in flash

light. This light remains lit for as long as you

keep this button depressed.

The walkie-talkie doesn’t need to be switched

on to use this function.

Attention: Don’t stare directly into the light when

lit and don’t shine it in other people’s eyes.

The light can be bright and may damage your

eyesight.

ADDITIONAL FUNCTIONS

VOX FUNCTION:

When the VOX function is enabled (VOX =

Voice Activated Transmission), the FR-175

starts sending as soon as you speak into the

microphone.

To switch the VOX function on/off:

1. press 3x the MENU button, the word “VOX”

will illuminate in the left part of the display

2. use the buttons or to set the trigger sen-

sitivity (‘OF’ is off, ‘1’ is the lowest sensitivity,

‘3’ is the highest sensitivity)

3. press the P button to confirm

Preferably, use this function in combination with

headsets. Keep in mind that it can take over a

second after you’ve started talking before the

walkie-talkie enables the transmitter.

CHANNEL MONITORING: (listening)

Use this function to disable the noise reduction,

allowing you to also listen to weak transmitters

on the current channel.

To switch the MONITOR function on/off:

1. press and hold the button for 2 seconds to

disable the noise reduction and to monitor the

channel

2. release the button to turn the noise reduc-

tion on again

CHANNEL SCAN:

Use the scan function to listen in on all channels

one after the other.

1. Press and hold the button for 2 seconds to

start the scan

2. briefly press the or button to continue

scanning if you’re only receiving noise on a

certain channel

3. press the P or MENU button to end the scan

KEYPAD LOCK:

When the keypad lock is activated, the , and

MENU buttons are blocked.

1. press and hold the MENU button until

appears in the display after approx. 2 sec-

onds

2. press and hold the MENU button again for

2 seconds to release these buttons again

FR-175

SCAN

VOX

Microphone

Flash light

Headset output

Antenna

Display

P button

(send button)

Charging contacts

(rear)

Speaker

SCAN

VOX

1.5V AAA

Alecto FR-175 Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Alecto FR-175

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info