Bedienungsanleitung Alecto SCA04 (Seite 51 von 54) (Deutsch, Englisch, Holländisch, Französisch)

794857

Zoom out

Zoom in

Vorherige Seite

1/54

Nächste Seite

10 minutes the concentration is still above 200PPM the alarm will be activated again. During the hush

function, press the test button to immediately disable the hush function and make the alarm audible.

LED INDICATION:

Red LED Alarm, carbon monoxide present

Yellow LED Sensor problem

Green LED Normal functioning, the LED ashesevery45seconds

BATTERY INFORMATION INDICATION:

1. Every 45 seconds the battery is automatically checked.

2. Every45secondsthegreenLEDwilllightupbrieyaslongasthetotalbatteryvoltageisabove3,6

Volt. This means that the battery capacity is okay. If the battery voltage drops below 3.6 Volts, the

yellow“Fault”1xLEDwillbrieylightuponceaminuteandaone-timebeepwillsound.Nowthe

batteries should be replaced as soon as possible.

Use High Energy Alkaline batteries (3 x LR6 / 1,5V AA). Rechargeable batteries are not suitable. The

supplied batteries will last approximately 24 months before they run out

REASON FOR SENSOR FAULT:

Faults can be caused by broken circuitry, a faulty sensor or faulty electronic parts.

SENSOR FAULT CAUSED BY CHEMICAL GASES:

When volatile chemical gases such as alcohol are the cause for error detection, this may be corrected by

switching the detector off and leave it in fresh air for 24 hours. This will restore the sensor. If the error is

not cleared after these 24 hours, the detector is faulty and should be replaced. Don’t repair the detector

yourself, but have it repaired by the importer.

When the alarm is contaminated and damaged by high concentrations of chemical gases, the sensor could

be affected. This will lead to a temporary error or permanent damage. When the alarm sounds and you

can smell a chemical gas, this could be the reason. Carbon monoxide is a colourless and odourless gas.

Chemical gases do have an odour.

The following substances and gases can cause false alarms or permanently damage the detector:

Methane, propane, iso-butane, ethylene, ethanol, alcohol, iso-propanol, benzene, toluene, acid, ether,

hydrogen, hepatic gas, sulphur dioxide, aerosol, propellant, alcohol preparation, paint, thinner, dissolvent,

bonding agents, shampoo, aftershave balm, perfume, car exhaust (cold start) and certain cleaning agents.

MAINTENACE:

To keep your CO detector in proper working order, please follow these easy steps:

• Once a month, check that the alarm is working properly by pressing the test button.

• Clean the CO detector with a vacuum cleaner or with a soft cloth or brush once every month to remove

excess dust.

• Check whether the batteries are damaged, exhausted or corroded.

• Explain to children that they should not play with the CO detector.

• Ensure children are aware of the dangers of carbon monoxide poisoning.

• Never use cleaning agents or other solutions to clean the CO detector.

• Never use air fresheners, hair spray or other aerosols near the CO detector.

• Don’t paint the CO detector. Paint covers the vents preventing the sensor from detecting CO.

• Never disassemble, repair or modify the product yourself; there’s a high risk that it will no longer

function correctly or reliably.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Alecto SCA04 Seite 51

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info