627483

Alecto WS-2200 Anleitung

1
Zoom out
Zoom in
Vorherige Seite
1/2
Nächste Seite
User’s manual
Weather station with wireless outdoor sensor
WS-2200
Overview:
Indoor unit:
1. Display:
Shows time, indoor and outdoor temperature and
weather forecast.
2. SNOOZE / LIGHT button :
Snooze button for the alarm function.
Also turns on the display lighting.
3. ALARM SET button :
For checking and setting the wake-up alarm.
4. CH/+ button:
Selection button when using multiple outdoor units
and the ‘+’ button during setup.
5. MEM/- button:
Memory button when checking min and max val-
ues and the ‘-’ button during setup.
6. DISPLAY SET button:
Function setup button.
7. °C / °F switch:
To switch the temperature display between
degrees Celsius and degrees Fahrenheit.
8. SENSOR button:
To pair the indoor unit with the outdoor unit.
9. RCC button:
To turn the DCF receiver on or off.
10. RESET button:
To restart the indoor unit in case of a (possible)
error.
11. Battery compartment.
Outdoor unit:
1. Monitor-LED:
Illuminates as soon as the outdoor unit is sending
measurement data to the indoor unit.
2. CH 1.2.3 switch:
To set the outdoor unit to a different channel.
3. RESET button:
To restart the outdoor unit in case of a (possible)
error.
4. Suspension eye:
Provision to suspend the outdoor unit from a wall.
5. Battery compartment.
Power supply:
Indoor unit:
Slide down the battery cover at the rear of the unit
and insert 2 AA 1.5V batteries according to the mark-
ings inside the battery compartment. Slide the battery
cover back onto the indoor unit.
The indoor unit will now start a 1 minute scan to
search for the outdoor unit. Therefore, you’ll need to
insert the batteries into the outdoor unit within that
minute.
Outdoor unit:
Slide down the battery cover at the rear of the unit,
slide the CH switch to the position ‘1’ and insert 2 AA
1.5V batteries according to the markings inside the
battery compartment. Slide the battery cover back
onto the outdoor unit.
Weak battery warning:
As soon as the batteries of the outdoor unit become
exhausted, the symbol will illuminate on the
display of the indoor unit.
Now please replace the batteries of the outdoor unit.
The indoor unit does not provide a battery warning.
Replace the batteries of this unit as soon as the
display becomes dim or weak.
Pairing the indoor unit / outdoor unit:
Automatically:
As soon as you insert the batteries into the indoor
unit, the indoor unit will start a 1 minute scan to
search for the signal of the outdoor unit. Therefore,
if you insert the batteries into the outdoor unit within
that minute and the units will ‘nd’ each other, they
will be automatically paired and the display of the
indoor unit will show the temperature transmitted by
the outdoor unit.
Manually:
If the units cannot be paired automatically, or after
replacing the batteries, you can pair the outdoor unit
(again) with the indoor unit as follows:
1. use a sharp object to briey press the RESET
button on the rear of the indoor unit
2. use a sharp object to briey press the RESET
button on the rear of the outdoor unit
3. the units will nd each other (again) after several
seconds and the indoor unit will display the tem-
perature transmitted by the outdoor unit.
Clock:
Introduction
The WS-2200 is provided with a built-in DCF receiver
which receives the DCF time signal from Frankfurt.
This signal ensures that the clock shows the time
very accurately, provided a strong enough signal is
being received.
Automatically:
As soon as you insert the batteries into the indoor unit,
the clock will start searching for the DCF radio signal
for the time while the antenna symbol is ashing.
After several seconds or minutes the WS-2200 will
start showing the correct time. In extreme cases, it can
take over a day before the DCF time is shown.
Manually:
If the clock cannot receive the radio signal or cannot
receive it well enough, you can set the clock manually
as follows:
1. press and hold the DISPLAY SET button for
2 seconds, 12Hr or 24Hr will appear in the display
2. use +/- to set the time format, then briey press
the DISPLAY SET button
3. use +/- to set the hours and then briey press the
DISPLAY SET button
4. use +/- to set the minutes and then briey press
the DISPLAY SET button
5. use +/- to set the seconds to 0 (this allows you to
have the clock run synchronously with your own
clock) and then briey press the DISPLAY SET
button
6. use +/- to set the hour difference compared to the
DCF time. E.g. for use in the Benelux select ‘0’
and then briey press the DISPLAY SET button
The clock is now set manually.
When the DCF receiver is enabled and a strong
signal is being received, the receiver will overwrite
the clock display.
Switching the DCF receiver on/off:
You can turn off the DCF receiver as follows, allowing
you to have only the time and date shown on the
display according to your programming:
• turn off: press and hold the RCC button at the
rear of the indoor unit for 4 seconds until the
antenna symbol disappears.
You can turn the receiver back on as follows:
• turn on: briey press the RCC button at the rear of
the indoor unit until the antenna symbol starts
ashing
‘DST’ in the display.
‘DST’ stands for Daylight Saving Time.
‘DST’ illuminates when the displayed time is the
daylight saving time.
1 2 3 4
1
2
36
54
7
8
9
10
11
433MHz
THERMO SENSOR
RESETCH 1 2 3
1

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln
1

Forum

alecto-ws-2200

Suche zurücksetzen

  • Alecto WS-4700 neu, empfängt kein Zeitsignal uns Uhr mit Datum kann auch nicht manuell eingstellt werden
    Wagner Eingereicht am 21-2-2021 10:07

    Antworten Frage melden

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Alecto WS-2200 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Alecto WS-2200

Alecto WS-2200 Bedienungsanleitung - Deutsch - 2 seiten

Alecto WS-2200 Bedienungsanleitung - Holländisch - 2 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info