Bedienungsanleitung Alecto WS-3850 (Seite 5 von 56) (Deutsch, Englisch, Holländisch, Französisch)

794960

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

1. Open the battery compartment at

the back of the indoor unit.

2. 

all the way to the left.

3. Insert the second battery and

slide it again to the left.

4. Insert the third battery.

5. Finally, replace the battery cover.

Hang or stand:

The indoor unit can either be placed freestanding on a cabinet or desk (fold

out the stand on the back of the indoor unit for this purpose) or the unit can

be hung on the wall (see keyhole openings on the back).

4.2 Outdoor units:

General installation and placement tips:

• First, check that the outdoor units are within reach of the indoor unit

before permanently mounting the outdoor units. Keep the distance

between the outdoor units and the indoor unit to within 30 meters.

• Ensure that the outdoor units are placed at least 1,5 meters above the

ground and freely exposed to the rain and wind.

• In order for the outdoor units to work as accurately as possible, they

must stand as horizontal as possible. For the outdoor rain unit, check

that the surface is level before mounting.

• To indicate which direction the wind is coming from, the outdoor wind

unit must be oriented to the South. See the S designation at the

bottom of the outdoor unit for this. Use the compass on the outdoor

wind unit to correctly orientate the unit.

• Make sure the outdoor units hang and/or stand freely. The wind speed

meter and the wind vane, in particular, should hang in direct wind.

AAA 1,5V AAA 1,5V AAA 1,5V

• Find a location where the likelihood of blowing leaves is minimal.

󰀨

measurement results. In any event, we advise you to place the outdoor

units in such a way that it is fairly easy to remove any leaves and to

replace the batteries.

• Perhaps the outdoor units can be located within reach for a week to try

out all functions. Check that everything is functioning properly before

placing the outdoor units in their permanent location.

4.3 Outdoor unit wind:

Registration:

First register the outdoor units with the indoor unit before permanent

placement of the outdoor units Once the indoor unit batteries are installed, it



After the 5 minutes, the indoor unit can be manually set to receive. To do

this, press the channel button for 2 seconds to set the indoor unit to

receive mode.

Insert 4 x 1,5V AA batteries in the outdoor wind unit. See diagram. Set the

Channel switch to the same channel selected on the indoor unit. Then press

the TX key. Check that the indoor unit has received the signal. Press the

TX button once more, if necessary. The outdoor temperature and humidity

are displayed on the indoor unit via the outdoor wind unit.

The outdoor wind unit is registered

when the information appears on

the display.

󰀨

reception, press the “WAVE” key.

To turn the DCF-77 reception on

again, register the outdoor unit



and reinserting the batteries

and repeating the registration

procedure.

AA 1,5V

WAVE

1 2 3

WAVE

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Alecto WS-3850 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info