Bedienungsanleitung Alecto WS-4900 (Seite 60 von 72) (Deutsch, Englisch, Holländisch, Französisch)

708530

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

3. INSTALLATION

Attention: after the installation, it may take several hours up to a day before the correct values are

displayed.

Attention: the indoor unit is powered by the supplied power adaptor. For

backup power, you may insert the included 3V CR-2032 button cell

battery.

3.1 Power supply:

Indoor unit:

The indoor unit is powered by the supplied power adaptor with micro USB plug.

The model number of this adaptor is: HX12-0500500-AG. Only use this adaptor.

Insert the plug of this adaptor into the rear of the indoor unit according to the

picture below and insert the adaptor into a 230V wall socket.

Use a coin to unscrew the battery cover for

the backup battery by turning it anti-clockwise

and insert a CR-2032 button cell battery (not

incl.) according to the markings inside the battery compartment (minus pole

downwards). Replace the battery cover and lock it by using the coin and

turning the battery cover a little clockwise. See also ‘OPEN’ and ‘CLOSE’

on the battery cover.

Outdoor unit:

Open the battery compartment by loosening the battery cover using a small

crosshead screwdriver. Insert 3 x size AA 1.5V batteries according to the gure

below, paying attention to the polarity (+ and -). Replace the cover (batteries are

not included).

Advice regarding the batteries for the outdoor unit:

Because normal alkaline batteries do not perform or do not perform well at temperatures around or below

0°C, the use of standard alkaline batteries in the outdoor unit is not recommended. For the outdoor unit,

we therefore recommend installing Lithium batteries that have been designed to function at a temperature

range of -20°C to 60°C. These batteries are available through the service department of Alecto via internet

www.alecto.info

The lifespan of Lithium batteries with a capacity of 2900mAh is well over a year.

3.2 Pairing indoor unit / outdoor unit:

Automatically:

As soon as the batteries are inserted into the indoor unit, the indoor unit starts searching for a signal from

the outdoor unit for 1 minute. So, if you have installed batteries in the outdoor unit within that minute and

these units ‘nd’ each other, they will automatically connect with each other and the display of the indoor

unit will show the temperature, humidity, rainfall amount, wind speed and the wind direction as the outdoor

unit transmits this data.

Manually:

If the units cannot be paired automatically, or after replacing the batteries, you

can pair the outdoor sensor (again) with the weather station unit as follows:

1. Briey press the SENSOR button at the rear of the indoor unit, the antenna

symbol in the display starts ashing

2. Briey press the RESET button on the outdoor unit.

3. The units will have found each other (again) after several seconds

reset

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Alecto WS-4900 Seite 60

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info