Bedienungsanleitung Alesis IO14 (Seite 38 von 70) (Englisch)

693657

Zoom out

Zoom in

Vorherige Seite

1/70

Nächste Seite

Hardware Direct Monitoring

1. Output Monitor Tabs

Use these tabs to select the output pairs to which you will blend in

the incoming signal. Each tab’s HDM mix is completely separate

from the others.

Setting up direct monitor mixes for single musicians and for

multiple musicians

Most commonly, you’ll have a stereo set of speakers attached to

outputs 1/2. This is the output pair to use for your Digital Audio

Workstation’s stereo outputs.

If you are recording a single musician, connect your inputs, and

then select the tab for outputs 1/2. Now, you can easily blend in

the musician’s direct audio with the music coming back from the

Digital Audio Workstation.

When you are recording multiple musicians—each of whom

desires a different monitor mix—use these tabs to create a separate

“monitor mix” for each output pair.

Experiment with creating multiple mixes—doing so puts no strain

on your computer.

2. Pan/Mute/Solo

Set the left/right pan position of the audio here. Also, you can

solo and mute individual channels.

Using the Shift key, click the pan knob to return it to center. Also,

hold down Shift while clicking to mute or solo (or un-mute or un-

solo) all of the inputs at one time.

3. Volume

Set the volume using this slider.

4. Stereo Channel Linking and Unlinking

Use this button to link or unlink the controls for stereo channel

pairs.

5. Channel Names

Just like the output tabs, the incoming audio channels can be re-

named. (Words like “vox” and “snare” probably have more value

than “Analog1” and “ADAT12.”) The names you provide carry

over to all of the tabs.

6. Master HDM Mix Fader

This is the master fader for the Direct Monitor mix for this output

pair. Bringing this fader up or down affects all the channels being

monitored using HDM but does not affect the audio coming back

from the computer.

Once you have set your balances for multiple instruments using

the individual slider, this control allows you to bring your whole

mix into balance with the audio from your Digital Audio

Workstation.

At 176.4k and 192k sample

rates, hardware direct

monitor mixes can only be

heard on outputs 1-4. Audio

will play back from the

computer as normal on all

the channels, but the analog

and digital inputs cannot be

monitored on outputs 5-8.

f you hear the input signal

twice—with a short delay

between each instance—

then you are most likely

monitoring through both the

HDM panel and also your

DAW software. Either turn

off input monitoring on your

DAW or mute the

corresponding input on the

HDM panel.

-naming the tabs

You can re-name each of

these tabs by double-clicking

on them and entering your

new name. (Names like

“Singer” and “Drummer”

can be a lot more helpful than

“Out 3-4.”) Note that the

names you type will not alter

the physical routing taking

place in th

e IO14/26.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Alesis IO14 Seite 38

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Alesis IO14

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info