Bedienungsanleitung Alesis MultiMix 12R (Seite 18 von 62) (Englisch)

693707

Zoom out

Zoom in

Vorherige Seite

1/62

Nächste Seite

Connections

Multimix 12R Reference Manual 7

CONNECTIONS

Inputs

Cable common sense

Make all connections to the Multimix 12R with the power turned off

wherever possible. If you must connect or disconnect inputs while

power is on, make sure the channel fader and [TRIM] are turned all the

way down to avoid sudden pops and clicks which may damage

speakers or other equipment.

Use good-quality cable: 99% of all mixer problems turn out to be

cable or connector problems. Use the best quality cable you can, for

highest reliability and lowest noise. If something goes wrong, check

the cable and its connection to the mixer first. If the connectors are

dirty or corroded, clean them with isopropyl alcohol or other

approved electrical contact cleaner before inserting them into the

Multimix 12R. High quality cables are low-capacitance shielded cables

with a stranded (not solid) internal conductor and a low-resistance

shield. Although quality cables cost more, they do make a difference.

Route cables in your system correctly by observing the following

precautions:

• Do not bundle audio cables with AC power cords.

• Avoid running audio cables, or placing the Multimix 12R itself,

near sources of electromagnetic interference such as transformers,

monitors, computers, etc.

• Never unplug a cable by pulling on the wire itself. Always unplug

by firmly grasping the body of the plug and pulling directly

outward.

• Do not place cables where they can be stepped on. Stepping on a

cable may not cause immediate damage, but it can compress the

insulation between the center conductor and shield (degrading

performance), or reduce the cable’s reliability.

• Avoid twisting the cable or having it make sharp, right angle turns.

Connections

Microphone Inputs

The Alesis Multimix 12R features eight studio-grade, low-noise hybrid

microphone preamplifiers. These [MIC] jacks are designed to work

with almost any low-impedance microphone using standard 3-

conductor XLR connectors. The [MIC] jacks also feature 48 volt

phantom power, which may be turned on and off by the [PHANTOM]

switch on the back panel, for condenser microphones which require

external powering.

Balanced Mic Input

Ground

Hot

Cold

Socket (female)

The MIC Input is designed to accept a wide range of balanced or

unbalanced low impedance input signals, with up to 60 dB of

amplification available (which is 10 to 20 dB more than many other

rack-mount mixers). It is wired with "pin 2 hot" according to the

accepted standard.

✪ Use only one input per channel. The LINE IN jack and the MIC IN

jack of a channel can’t be used at the same time. If you turn up the

level of a line source to hear it at the same time a microphone is

connected, you may damage the microphone.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Alesis MultiMix 12R Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info