Bedienungsanleitung Allen-Heath GL 3300 (Seite 12 von 20) (Englisch)

541351

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

GL3300 U

SER

UIDE

8 AUX SENDS provide ample feeds for foldback monitors and effects. These

are in two groups of four each with a POST/PRE switch to source the sends either

pre-fader or post-fader.

AUX 1-4 feed balanced XLR outputs capable of driving long cable runs and

include INSERT points. These are normally used to provide MONITOR SENDS

to the performers and stage crew, although they can be used for additional effects.

Plug a graphic EQ into the insert to 'ring out the monitor' (tune) to the stage

acoustics to minimise feedback. The effect of the EQ can be listened to using the

aux master AFL system. Monitor sends are usually set pre-fade, although some

sources such as radio mics can be set post-fade to avoid 'dressing room' talk spill.

Note stereo input channel aux sends are the mono sum of left and right.

AUX 5-8 feed jack outputs and are normally used to provide EFFECTS SENDS

to external devices such as reverb and delay effects units. Effects sends are set

post-fade so that the amount of effect (wet signal) is always relative to the position

of the fader (dry signal). Adjust the amount of effect required for each channel

using its AUX control. The effect is returned to the mix through another channel,

usually the stereo return described later in this guide.

Note; when the GRP/AUX REVERSE 5-8 switches are pressed in the master

section AUX SENDS 5-8 feed XLR outputs with inserts. GROUPs 5-8 are re-

routed to AUX 5-8 jack outputs.

POST-FADE sends are always post-EQ, post-mute. PRE-FADE sends are set

post-EQ, post-mute as standard, but may be internally reset to be pre-EQ, pre-mute

or post-EQ, pre-mute. Each AUX SEND may be internally set to be permanently

pre or post-fade rather than follow the panel switch. Refer to the Internal Link

Options section in this user guide.

PAN positions the channel signal between the Left L and Right R outputs when

the L-R ROUTING switch is pressed. PAN also positions the channel signal

between the ODD groups e.g. 1, 3, 5, 7 and EVEN groups e.g. 2, 4, 6, 8 when the

ROUTING switches are pressed. This lets you position the sounds within a stereo

image. In this way subgroups may be set up in mono by turning the PAN fully left

L or right R or in stereo by setting PAN between L and R to feed a pair of groups.

MUTE switches the signal off when pressed. A muted channel is indicated by the

illuminated switch. The channel meter continues to indicate pre-mute and fader

channel activity. The mute switch also illuminates when the channel is muted by

one of the 4 MUTE GROUPs.

Switches M1, M2, M3, M4 next to the fader, assign which mute group the input

channel will be assigned to. This is controlled by the MUTE GROUP switches

located in the master section.

A 100mm long throw FADER provides +10dB boost above the normal '0'

operating level.

A 3 LED CHANNEL METER system shows signal activity at all times. The green

SIG LED indicates signals greater than -20dBu, the yellow '0' LED represents

normal operating level, and the red PEAK LED warns of potential overload 5dB

before clipping. Set the channel so that the meter averages '0'. Back the gain off

if the red peak LED flashes.

Pressing PFL automatically interrupts the headphone monitor signal to let you

listen to the channel pre-fader signal without interrupting the main console

outputs. The signal level is shown on the LR monitor bargraph meters, and on the

Mono/PFL meter if the optional meterpod is fitted. In this way each sound can be

correctly lined up and checked at any time.

DIRECT OUT taps the signal off post fader for connection to external processing

or recording equipment. This is ideal for multitrack recording during live

performance as each channel can be recorded onto a separate track for mixdown

later. The direct out signal can be set pre-fader if the internal link option is changed.

Refer to the Internal Link Options section in this user guide.

8 AUX SENDS

Normal fader

position

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Allen-Heath GL 3300 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info